100% Guarantee CCNA Collaboration 210-065 vce

Q1. An engineer is configuring a Cisco TelePresence System endpoint for use with a maximum of six people in the room. Which table type should be configured when setting up cameras where two participants directly face the endpoint display? 

A. short racetrack 

B. long racetrack 

C. short rectangle 

D. long rectangle 

View Answer

Q2. Refer to the exhibit. 

A call with a destination alias of 15551001234 reaches a Cisco TelePresence VCS. Which transform will the destination alias match? 

A. Transform 1 

B. Transform 2 

C. Transform 3 

D. Transform 4 

View Answer

Q3. An engineer is configuring VIP mode for a Cisco TelePresence Multipoint Switch. What are three characteristics the engineer must keep in mind? (Choose three.) 

A. VIP mode can be configured only when the meeting is not active. 

B. The VIP is displayed on the center screen for three screen systems. 

C. Network multipoint meetings are supported. 

D. VIP mode timers must be configured from the CLI. 

E. Locking is not supported. 

F. Only one VIP can be configured for each meeting. 

View Answer

Q4. An important Cisco TelePresence video multipoint call is in progress and you are getting complaints of pixilation of the video and poor audio quality on one of the involved systems. 

Which page would be a good place to start for troubleshooting the issue on the affected endpoint? 

A) 

B) 

C) 

D) 

A. Exhibit A 

B. Exhibit B 

C. Exhibit C 

D. Exhibit D 

View Answer

Q5. efer to the exhibit. 

Which configuration item shown in the exhibit should be used to assign the internal and external video communication server address for this group of users? 

A. User Settings > Video Address pattern 

B. Administrative Tools > User Settings 

C. Configuration Template > Edit Template 

D. User Import > Configuration 

View Answer

Q6. Refer to the exhibit. 

An administrator is attempting to register a Cisco TelePresence endpoint to a Cisco VCS. 

The Cisco VCS uses local authentication and a single username for all endpoints. Where is the first place that the administrator should go to resolve the issue? 

A. VCS > Configuration > Authentication > Devices > Local Database 

B. Endpoint > Configuration > System Configuration > Profile 1 > Authentication 

C. VCS > Configuration > Authentication > Outbound Connection Credentials 

D. Endpoint > Configuration > System Configuration > SIP > Profile 1 > Authentication 1 

E. VCS > Configuration > Registration > Allow List 

F. VCS > Configuration > Registration > Deny List 

View Answer

Q7. Which Cisco TelePresence Multipoint Control Unit Layout view mode gives prominence to one conference participant over the other conference participants while still allowing conference participants to view multiple participants at the same time? 

A. enhanced continuous presence 

B. active speaker 

C. continuous presence 

D. room switching 

E. speaker switching 

View Answer

Q8. Which Cisco Video Surveillance device is responsible for providing video streams to monitors after the respective layouts and views are received by the monitors? 

A. Cisco IP Video Surveillance Operations Manager 

B. Cisco IP Video Surveillance Virtual Matrix Viewer 

C. Cisco Video Surveillance Manager 

D. Cisco Video Surveillance Media Server 

View Answer

Q9. A technician has installed and powered on a Cisco TelePresence MCU 5320 and is connected via the console port. The technician needs to determine the IP settings that were automatically assigned via DHCP. Which command should be entered? 

A. xstatus 

B. show network eth0 

C. status 

D. help static 

View Answer

Q10. A network engineer wants to automate the monitoring of Cisco TelePresence TX systems. Which step should the engineer take first? 

A. Configure Cisco TMS on the codec. 

B. Configure Medianet on the codec. 

C. Configure NTP on the codec. 

D. Configure Multiway on the codec. 

E. Configure SNMP on the codec. 

View Answer