Proper study guides for Renovate Cisco Implementing Cisco Video Network Devices v1.0 certified begins with Cisco 210-065 preparation products which designed to deliver the Exact 210-065 questions by making you pass the 210-065 test at your first time. Try the free 210-065 demo right now.


2026 New 210-065 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/210-065/

Q1. In this item, you will need to use all information presented to you to successfully answer the question. 

Refer to the exhibits. An administrator needs to perform a factory reset on a C-Series endpoint. What are two valid ways to accomplish this task? (Choose two.) 

A. Exhibit A 

B. Exhibit B 

C. Exhibit C 

D. Exhibit D 

E. Exhibit E 

Answer: C,D 

Q2. A Cisco TelePresence System 1300 Series endpoint is in the process of booting and the engineer notices a red "X" on the screen for Step 6 in the boot process. What does this red "X" indicate? 

A. The endpoint failed to load its firmware. 

B. There is an error with compact flash. 

C. The endpoint could not obtain an IP address via DHCP. 

D. The touch panel is malfunctioning. 

Answer: B 

Q3. Which three features are supported by the Cisco Video Surveillance Encoding Server? (Choose three.) 

A. IP and analog cameras 

B. MPEG-2 and MPEG-4 encoding 

C. archiving 

D. motion detection 

E. clustering 

F. virtual matrix 

Answer: A,C,D 

Q4. Which statement is true about the Cisco TelePresence System 500-32 system regarding the HVAC needs for the room where it is installed? 

A. The system does not require any additional requirements above the normal HVAC requirements for the room. 

B. You must supply additional cooling requirements for the room. 

C. You must supply a room that has energy-efficient lighting to reduce the temperature of the room. 

D. The temperature of the room will be 10 to 20 degrees warmer than the rest of the building. 

Answer: A 

Q5. Which of these involves combining visual elements from separate sources into a single image? 

A. interlacing 

B. compositing 

C. video conferencing 

D. interleaving 

Answer: B 

Q6. Refer to the exhibit. 

The customer recently connected a new TV monitor to the Cisco TelePresence endpoint. This device is now showing a warning concerning the echo cancellation delay. Which action could help mitigate this issue? 

A. Turn off any postprocessing settings. 

B. Turn off 3D mode on the new TV. 

C. Turn on Frequency Scan Acceleration for the new TV. 

D. Turn off surround sound on the new TV. 

Answer: A 

Q7. Refer to the exhibit. 

What can be deduced from the log shown in the exhibit, which was taken from a Cisco TelePresence Codec C60? 

A. A direct call to 52902511 is being made. 

B. A Multiway call to multiway221@osl147.local is being made. 

C. No calls are being attempted by the endpoint. 

D. A BFCP call is being initiated. 

E. The endpoint is receiving a call from the VCS. 

Answer: B 

Q8. Refer to the exhibit. 

Under which tab can the registration status for the endpoint be found? 

A. Diagnostics 

B. Configuration 

C. Call Control 

D. Maintenance 

Answer: A 

Q9. Which two of these are considered to be provisioning and scheduling management tools in a Cisco TelePresence environment? (Choose two.) 

A. Cisco TelePresence Manager 

B. Cisco Video Surveillance Operations Manager 

C. Cisco TelePresence Management Suite 

D. Cisco TelePresence Multipoint Control Unit 

E. Cisco Video Surveillance Management Server 

Answer: A,C 

Q10. Refer to the exhibit. 

A technician is reviewing the search history details on a Cisco TelePresence VCS for a recent call that failed. What was the cause for the call setup failure? 

A. A local call policy rule denied the call. 

B. The source alias matched an entry in the registration deny list. 

C. The originating caller was not authenticated. 

D. The source alias origin is unknown. 

Answer: A