It is impossible to pass Cisco 210-065 exam without any help in the short term. Come to Actualtests soon and find the most advanced, correct and guaranteed Cisco 210-065 practice questions. You will get a surprising result by our Up to the minute Implementing Cisco Video Network Devices v1.0 practice guides.


2026 New 210-065 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/210-065/

Q1. Management would like to set up a permanent recurring Cisco TelePresence meeting where the team would dial into to a preconfigured number. Which meeting type should be used? 

A. scheduled conference 

B. ad hoc conference 

C. rendezvous conference 

D. multiway conference 

Answer: C 

Q2. A technician is tasked with performing a room readiness assessment in preparation for an immersive video endpoint. What are three Cisco best practices regarding lighting recommendations for the room? (Choose three.) 

A. The bulb temperature should be between 4000 and 4100K. 

B. Key lighting should be between 200 and 400 Lux with the endpoint powered on. 

C. Shoulder lighting should not exceed two times the facial lighting values with the endpoint off. 

D. Use direct lighting fixtures. 

E. Within the camera field of view, the lighting for all parts of the room should not fluctuate more than 100 Lux. 

F. Avoid using dimming light control systems. 

Answer: A,C,E 

Q3. A desktop video endpoint is needed that can support a PrecisionHD camera design and a built-in display, and is Bluetooth-ready and multisite-capable. Which desktop endpoint supports all of these requirements? 

A. SX20 

B. EX60 

C. SX80 

D. EX90 

Answer: D 

Q4. An engineer is configuring a Cisco TelePresence System endpoint for use with a maximum of six people in the room. Which table type should be configured when setting up cameras where two participants directly face the endpoint display? 

A. short racetrack 

B. long racetrack 

C. short rectangle 

D. long rectangle 

Answer: A 

Q5. What is the importance of defining option 150 in the DHCP server for Cisco TelePresence endpoints? 

A. Option 150 is not important. 

B. It is the TFTP server IPv4 address where the video endpoint retrieves its configuration file while booting. 

C. It is the IPv4 address of the default gateway for the subnet that the video endpoint is connected to. 

D. It is the configured SIP registrar and proxy server. 

E. It is the unique NTP server IPv4 address. 

Answer: B 

Q6. Which two methods can be used to set the default call protocol of a Cisco TelePresence endpoint running TelePresence codec firmware? (Choose two.) 

A. Use the GUI and set System > H.323 > Settings > Default Call Protocol > H.323. 

B. Use the CLI command xConfiguration Conference 1 DefaultCall Protocol: H323. 

C. Use the CLI command Conference Default Protocol: H323. 

D. Use the CLI command Default Protocol: H323. 

E. Use the GUI and set Configuration > System Configuration > Conference > DefaultCall > 

H.323. 

Answer: B,E 

Q7. In this item, you will need to use all information presented to you to successfully answer the question. 

The Cisco Telepresence Codec C90 is unable to call the Cisco IP Video Phone. Assuming that the calling search space has been configured correctly, which of the these can cause this issue? 

A. The Cisco Telepresence Codec C90 can only be registered to a Cisco Telepresence Video Communication Server. 

B. A multipoint control unit is required in order for the call to work. 

C. The Cisco Telepresence Codec C90 can only be registered as a SIP endpoint to Cisco Unified Communications Manager. H.323 is not supported. 

D. URI dialing has not been configured on Cisco Unified Communications Manager. 

E. The Cisco Telepresence Codec C90 Profile 1 > CallSetupMode must be configured as a gateway since Cisco Unified Communications Manager does not have a gatekeeper functionality. 

F. The Cisco Telepresence Codec C90 is not registered as a SIP endpoint on Cisco Unified Communications Manager. The Cisco Telepresence Codec C90 needs to be registered as both SIP and H.323. 

Answer: E 

Q8. Refer to the exhibit. 

An administrator is attempting to register a Cisco TelePresence endpoint to a Cisco VCS. 

The Cisco VCS uses local authentication and a single username for all endpoints. Where is the first place that the administrator should go to resolve the issue? 

A. VCS > Configuration > Authentication > Devices > Local Database 

B. Endpoint > Configuration > System Configuration > Profile 1 > Authentication 

C. VCS > Configuration > Authentication > Outbound Connection Credentials 

D. Endpoint > Configuration > System Configuration > SIP > Profile 1 > Authentication 1 

E. VCS > Configuration > Registration > Allow List 

F. VCS > Configuration > Registration > Deny List 

Answer: D 

Q9. Refer to the exhibit. 

A network engineer is attempting to register a Cisco TelePresence endpoint to a Cisco VCS. What is the most likely cause of this failure? 

A. The lab.local SIP domain is not configured in the Cisco VCS allow list for registration. 

B. The Cisco VCS failed to bind to the LDAP server, which is where the lab.local SIP domain is learned. 

C. The lab.local SIP domain does not exist on the Cisco VCS. 

D. The endpoint does not have the proper port assignments configured for SIP signaling. 

E. The endpoint uses the TCP protocol and the Cisco VCS is configured to allow only TLS for SIP registrations. 

Answer: C 

Q10. An engineer is configuring VIP mode for a Cisco TelePresence Multipoint Switch. What are three characteristics the engineer must keep in mind? (Choose three.) 

A. VIP mode can be configured only when the meeting is not active. 

B. The VIP is displayed on the center screen for three screen systems. 

C. Network multipoint meetings are supported. 

D. VIP mode timers must be configured from the CLI. 

E. Locking is not supported. 

F. Only one VIP can be configured for each meeting. 

Answer: B,D,F