Cause all that matters here is passing the Cisco 300-080 exam. Cause all that you need is a high score of 300-080 Troubleshooting Cisco IP Telephony and Video exam. The only one thing you need to do is downloading Exambible 300-080 exam study guides now. We will not let you down with our money-back guarantee.


2026 New 300-080 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-080/

Q1. Two phones in the same cluster and at the same site have a call currently connected. The site local H.323 PSTN gateway loses connection with Cisco Unified Communications Manager. Which two results do you expect? (Choose two.) 

A. SRST is active, and all the phones enter SRST mode. 

B. No incoming and outgoing calls are possible. 

C. Cisco Unified SRST is able to receive incoming calls. 

D. The current call is not disconnected. 

E. The phones display "CM Fallback Service Operating." 

Answer: B,D 

Q2. You are troubleshooting video quality issues on a.Cisco TelePresence TX9000 Series system..Which CLI command shows the total number of lost video packets and the received jitter during a call in progress? 

A. show call statistics video 

B. show.call statistics all 

C. show.call statistics detail 

D. show.call statistics video detail 

Answer: D 

Q3. Refer to topology and Exhibits below: After making a change to a manually configured MGCP gateway, what step should you take to ensure that the gateway accepts the changes and be operational? 

A. Issue the commands no MGCP, then MGCP. 

B. Issue the commands no SCCP. then SCCP. 

C. Issue the commands Shut, then no shut 

D. Issue the commands no CCM. then CCM. 

Answer: A 

Q4. Which CLI command monitors ILS replication progress? 

A. utils ils findxnode 

B. utils ils show peer info 

C. utils ils showpeerinfo 

D. utils ils lookup 

Answer: C 

Q5. Which two statements indicate something that can cause an IP phone to fail roaming when device mobility has been configured? (Choose two.) 

A. Device Mobility Mode is set to Off in the Cisco Unified Communications Manager service parameters while the device mobility configuration on the phone is set to default. 

B. No device mobility groups have been configured. 

C. No locations have been configured and assigned to the device pools. 

D. No physical locations have been configured and assigned to the device pools. 

E. No device mobility-related information settings were configured under the device pools. 

Answer: A,D 

Q6. When identifying Cisco TelePresence Endpoint traffic characteristics, which three statements are true? (Choose three.) 

A. Latency, jitter, and loss are measured in a round-trip fashion. 

B. Latency, jitter, and loss are measured unidirectionally. 

C. Latency and loss are measured at a packet level, based on RTP header sequence numbers and time stamps. 

D. Latency and jitter are measured at a packet level, based on RTP header sequence numbers and time stamps. 

E. Jitter is measured at a video frame level, by measuring the arrival time of the video frame versus the expected arrival time. 

F. Jitter is measured at a packet level, by measuring the arrival time of the packet versus the expected arrival time. 

Answer: B,C,E 

Q7. An IP phone that is connected through a Cisco Catalyst 3750 Series Switch is failing to register with the subscriber as a backup server. When the user presses the settings button on the phone, only the Cisco Unified Communications Manager publisher shows as registered. What is the most likely cause for this issue? 

A. The phone does not have the correct Cisco Unified Communications Manager group in the device configuration page. 

B. The Cisco Unified Communications Manager group that is applied through the device pool is misconfigured. 

C. The ip-helper address command for the subscriber is not configured on the switch port. 

D. The subscriber does not have the correct device pool configured. 

E. The enterprise phone configuration does not have the call control redundancy enabled. 

Answer: B 

Q8. Refer to the exhibit. 

You're tasked with staging configuration changes to add conference bridge functionality to an existing IOS voice gateway deployment. What command is missing for the configuration to be accepted by the IOS CLI? 

A. The command maximum conference-participants must be configured under the dspfarm profile. 

B. The Enhanced IOS Conference Bridge is not configured in Cisco Unified Communications Manager. 

C. The command dsp services dspfarm must be configured under the voice-card configuration. 

D. The dspfarm command under the voice card is missing. 

E. The dsp tdm pooling command under the voice-card is missing. 

Answer: C 

Q9. Which issue would cause an MGCP gateway to fail to register with Cisco Unified Communications Manager? 

A. missing the configuration command isdn bind-l3 ccm-manager under the ISDN interface 

B. mismatched domain name on the MGCP gateway and Cisco Unified Communications Manager gateway configuration 

C. misconfigured route group in Cisco Unified Communications Manager 

D. incorrect MGCP IP address specified in the gateway configuration in Cisco Unified Communications Manager 

Answer: B 

Q10. When a user attempts to log out from Cisco Extension Mobility service by pressing the services button and selecting the Cisco Extension Mobility service, the user is not able to log out. What is causing this issue? 

A. The Cisco Extension Mobility service has not been configured on the phone. 

B. The user device profile is not subscribed to the Cisco Extension Mobility service. 

C. The CTI service is not running. 

D. The logout URL that is defined for the Cisco Extension Mobility service is incorrect or does not exist under the IP Phone Services configuration. 

Answer: B