The Regenerate Guide To 300-360 pdf

Q1. An engineer is performing a predictive wireless design for a Parts Distribution Center, which requires data and location services. Which three requirements are inputs to the design? (Choose three.)

A. access points with directional antennas

B. continuous -67 dBm coverage from one access point

C. overlapping -75 dBm coverage from three access points

D. overlapping -67 dBm coverage from two access points

E. access points in IPS mode

F. continuous -72 dBm coverage from one access point

G. access points in corners and along perimeters

View Answer

Q2. The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm. What is the target value for the cell edge reading?

A. -62 dBm

B. -67 dBm

C. -60 dBm

D. -70 dBm

View Answer

Q3. An engineer would like to calibrate the RF environment to improve accuracy. Which wireless attribute is added to the floor-level calculation by calibrating the floor?

A. attenuation

B. TX power

C. multipath

D. SNR

View Answer

Q4. A customer has deployed an N+N redundant wireless infrastructure. In this deployment, the access points have been salt and peppered between controllers. What configuration would be necessary to cut down on the use of mobility tunnels for voice clients?

A. mobility anchor

B. KIS based CAC

C. media session snooping

D. re-anchor roamed voice clients

View Answer

Q5. A customer is deploying a mesh outdoor wireless network based on FCC standards where spectrum analysis shows significant radar energy propagating throughout the coverage area from a local weather station. Which channel must be excluded from the access points RRM calculation to avoid network disruption due to weather radar activity?

A. 132

B. 44

C. 11

D. 36

View Answer

Q6. An engineer plugs in a Cisco Aironet 2700 Series Access Point and it is running in low power. Which three power requirements should be verified? (Choose three.)

A. 802.3ac compliant

B. 802.3at compliant

C. AP requires 43 VDC to function in full power.

D. AIR-PWRINJ3 power injector should be used.

E. AP requires 57 VDC to function in full power.

F. AIR-PWRINJ4 power injector should be used.

View Answer

Q7. Which two options describe best practices that must be completed after a wireless installation is finished?

(Choose two.)

A. Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller isinstalled.

B. Consult with the customer to ensure that the IT staff has a complete set of design and installationdocuments.

C. Make sure the customer is aware that they should consider purchasing a support contract immediately afterthe installation is complete.

D. Spend time with the customer to show them the controller GUI and inform them how they can reach theCisco TAC if they have any problems.

E. Test all the customer’s wireless devices and applications to ensure they are working properly.

View Answer

Q8. Which two steps are associated with the active portion of the audit when a post-installation audit is performed with an auditing tool such as Ekahau? (Choose two.)

A. Check for co-channel interference by standing near an access point on one channel and watching for other access points that are on the same channel.

B. Verify smooth roaming.

C. Check to see if the signal level on other access points that are heard on the same channel is at least 19dBm weaker than the access point that you are next to.

D. Check that all channels are supported by the APs, regardless of client capabilities.

E. Verify that the network traffic of physical data rate and packet loss meets user requirements.

View Answer

Q9. An 802.11n implementation is being discussed. Users are satisfied with the potential 300- 450 Mbps throughput of new 802.11n APs. Which three bandwidth requirements are used to calculate per client bandwidth through an 802.11n AP network? (Choose three.)

A. 450 Mbps throughput is the client max for 5-GHz radio.

B. Channel bonding on 5 GHz is required for a client to have a 300 Mbps WiFi link.

C. 300 Mbps throughput is the client max for 2.4-GHz radio.

D. The remaining bandwidth is divided per device when more clients are connected to one AP.

E. 100 Mbps Ethernet switch port is a potential bottleneck.

F. CleanAir helps clear noise for 802.11n channel bonding to work.

View Answer

Q10. An engineer is assigned to replace an older data-grade autonomous wireless network with a Cisco controllerbased wireless network to meet Voice over WLAN needs. The customer also wants all existing cable infrastructure to be reused and no new cable be specified. How should the engineer respond to the customer’s requirements?

A. Implement the wireless network with the restraints and decrease the TPC neighbor threshold to increase Txpower to provide overlapping cell coverage at sufficient SNR to provide for Voice over WLAN service.

B. Implement the wireless network with the restraints and utilize high-gain antenna to provide overlapping cellcoverage at sufficient SNR to provide for Voice over WLAN service.

C. Inform the customer that the network will not likely function as desired and a post install survey with thepossibility of some new cable would be recommended.

D. Inform the customer that it is not possible to provide coverage and quality for Voice over WLAN usingexisting AP locations and an entire overbuild will be necessary.

View Answer