Actual of 300-360 torrent materials and questions pool for Cisco certification for IT engineers, Real Success Guaranteed with Updated 300-360 pdf dumps vce Materials. 100% PASS Designing Cisco Wireless Enterprise Networks exam Today!


2026 New 300-360 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-360/

Q1. After the completion of a site survey with Ekahau Site Survey tool, using the default color palette, it is noted that multiple areas are shown as white on the heat map when viewing 5 GHz signal strength data. What does this indicate about the signal strength?

A. The area is below the minimum threshold configured on the tool.

B. The area is below the detectable level and indicates no RF signal.

C. The area is below -100 dBm at coverage cell edge.

D. The area is below -67 dBm at coverage cell edge.

Answer: A

Q2. The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm. What is the target value for the cell edge reading?

A. -62 dBm

B. -67 dBm

C. -60 dBm

D. -70 dBm

Answer: B

Q3. Which two best practices should be considered when a customer wants to purchase and implement Voice over Wireless for Cisco 7925 IP Phones? (Choose two.)

A. Enable lower data rates for 2.4-GHz data WLAN and higher data rates for phones.

B. Use a separate Cisco Wireless Lan Controller.

C. Enable 802.1x and Cisco Centralized Key Management for phone authentication.

D. Use dedicated Access Points only for Voice over Wireless.

E. Set data for 2.4 GHz and voice for 5 GHz using separate SSIDs.

Answer: C,E

Q4. A hospital environment was designed to guarantee RF coverage at or better than -67 dBm in the 5 GHz spectrum. The customer mandates that RRM be used for DCA and TPC in both bands. After deployment, why do many of the legacy 802.11b/g devices have difficulty maintaining connectivity?

A. Excessive co-channel interference in the 2.4 GHz band exists.

B. Excessive overlapping channels in the 2.4 GHz band exists.

C. TPC drastically reduces Tx power in the 2.4 GHz band.

D. TCP drastically increases Tx power in the 2.4 GHz band.

Answer: C

Q5. An engineer is planning for a 24 Mbps data rate for a new installation. What is the coverage area from the AP if the environment and other factors are not taken into consideration?

A. 225 feet

B. 80 feet

C. 150 feet

D. 100 feet

Answer: A

Q6. What is the recommended minimum speed at the edge of the cells in an 802.11g network for a good Cisco VoWLAN deployment?

A. 11 Mb/s

B. 36 Mb/s

C. 12 Mb/s

D. 18 Mb/s

Answer: C

Q7. An engineer installed a 3702 AP and is getting power from the switch. What is the reason for getting 3x3 MIMO instead of 4x4?

A. 802.1p 

B. 802.3af 

C. 802.11e 

D. 802.3at

Answer: B

Q8. An engineer must design wireless coverage in thick-walled stairwells. Which information should the engineer refer to when determining where APs can be installed?

A. Local or National Building Code

B. IEEE

C. BICSI TDMM

D. Cisco Hardware Installation Guide

Answer: D

Q9. An engineer is preparing for an indoor wireless LAN survey and is provisioning a survey kit. Which three pieces of equipment should be included? (Choose three.)

A. external connector access point

B. integrated antenna access point

C. coax low-loss cable

D. battery operated power supply

E. range finder

F. Yagi antennas

Answer: B,D,E

Q10. An engineer is assigned to replace an older data-grade autonomous wireless network with a Cisco controllerbased wireless network to meet Voice over WLAN needs. The customer also wants all existing cable infrastructure to be reused and no new cable be specified. How should the engineer respond to the customer’s requirements?

A. Implement the wireless network with the restraints and decrease the TPC neighbor threshold to increase Txpower to provide overlapping cell coverage at sufficient SNR to provide for Voice over WLAN service.

B. Implement the wireless network with the restraints and utilize high-gain antenna to provide overlapping cellcoverage at sufficient SNR to provide for Voice over WLAN service.

C. Inform the customer that the network will not likely function as desired and a post install survey with thepossibility of some new cable would be recommended.

D. Inform the customer that it is not possible to provide coverage and quality for Voice over WLAN usingexisting AP locations and an entire overbuild will be necessary.

Answer: C