10 Tips For Latest 300-080 practice test

Q1. Refer to the exhibit. 

When a call between two HQ users was being conferenced with a remote user at the BR site, the conference failed. Which configuration would be needed to solve the problem? 

A. The BR_MRG must contain the transcoder device. The BR_MRGL must be assigned to the BR phones. 

B. The HQ_MRG must contain the transcoder device. The HQ_MRGL must be assigned to the HQ phones. 

C. A transcoder should be configured at the remote site and assigned to all remote phones through the BR_MRGL. 

D. The HQ_MRG must contain the transcoder device. The HQ_MRGL must be assigned to the software conference bridge. 

E. Enable the software conference bridge to support G.711 and G.729 codecs in Cisco Unified Communications Manager service parameters. 

View Answer

Q2. When dialing any external SIP URI for a business-to-business call, an endpoint that is registered to the Cisco VCS Control fails to locate the remote endpoint. The same endpoint can successfully call another endpoint that is registered to the Cisco VCS Expressway. How do you resolve this issue? 

A. Add traversal call licensing on the Cisco VCS Expressway. 

B. Add traversal call licensing on the Cisco VCS Control. 

C. Add a multisite option to the endpoint. 

D. Configure a proper DNS zone on the Cisco VCS Expressway. 

E. Configure a traversal zone between the Cisco VCS Control and the Cisco VCS Expressway. 

F. Configure a SIP route pattern in Cisco Unified Communications Manager. 

View Answer

Q3. Which command is used on an IOS Router.that is.acting as a SAF Forwarder to confirm its registration status with a SAF Client? 

A. show ip asf-forwarder status details 

B. show ospf neighbor details 

C. show ip interface details 

D. show cdp neighbor details 

E. show eigrp service-family ipv4 clients details 

F. show service-family asf-forwarder details 

View Answer

Q4. Refer to topology and Exhibits below: Which command can be used to obtain the status of an MGCP gateway from the IOS device, as shown in the given output? 

A. show mgcp registration 

B. show mgcp-gw 

C. show mgcp connection 

D. show ccm-manager 

View Answer

Q5. Which two troubleshooting tools would initially be the best to use when troubleshooting the PSTN gateway side of a call routing issue while using Cisco Unified Communications Manager? (Choose two.) 

A. RTMT trace output 

B. Cisco IOS debug commands 

C. Dialed Number Analyzer output 

D. Cisco Unified Communications Manager alerts 

E. Cisco IOS show commands 

View Answer

Q6. You have been presented with a trouble ticket from an end user who works at a remote location that is served by a Cisco Unified Communications Manager Express. The user reports being unable to place calls to international numbers, but all other calls work properly and other users at this location can place international calls. Which two troubleshooting techniques would be helpful in resolving this issue? (Choose two.) 

A. Cisco IOS debug tools 

B. Class of Restriction baseline configuration for the user on Cisco Unified Communications Manager Express 

C. show output of the ephone and ephone-dn configurations 

D. show output of the voice translation rules in the voice gateway 

E. show output for the T1 controller and voice port configuration in the voice gateway 

View Answer

Q7. A user using a CP-9971 SIP phone reports that during a video call, the video portion of the call freezes. What should you do in order to point to and troubleshoot the issue? 

A. Restart the phone. 

B. On the phone, navigate to Administrator Settings > Status > Call Statistics > Video > Video statistics > Rcvr Packets statistics. Verify if the phone is receiving packets. 

C. Make sure that the camera is connected to the USB. 

D. Verify if the camera shutter is open. 

E. Perform a factory reset of the phone. 

View Answer

Q8. Which statement indicates something that can cause an inbound PSTN call to an H.323 gateway that is configured in Cisco Unified Communications Manager to fail to ring an IP phone? 

A. The gateway is not registered in Cisco Unified Communications Manager. 

B. The gateway IP address that is configured in Cisco Unified Communications Manager does not match the IP address that is configured at the gateway in the h323-gateway voip bind srcaddr command. 

C. The Cisco Unified Communications Manager does not have a matching route pattern to match the called number. 

D. The gateway is missing the command allow-connections h323 to h323 under the voice service voip configuration. 

View Answer

Q9. Refer to Exhibit: After reviewing the trace in the exhibit, what was the Directory number of the called party? 

A. 2001 

B. 5010 

C. 1905 

D. 2003 

View Answer

Q10. Refer to Exhibit: 

After reviewing the trace in the exhibit, what was the Directory number of the calling party? 

A. 2001 

B. 5010 

C. 1905 

D. 2003 

View Answer