Avant-garde Cisco 300-101 practice test

Question No: 3

When a packet is denied by an IPv6 traffic filter, which additional action does the device perform?

A. It scans the rest of the ACL for a permit entry matching the destination

B. It generates a TCP Fin bit and sends it to the source.

C. A creates a null route for the destination and adds it to the route table

D. It generates an ICMP unreachable message for the frame.

View Answer

Question No: 4

Refer to the following command: router(config)# ip http secure-port 4433 Which statement is true?

A. The router will listen on port 4433 for HTTPS traffic.

B. The router will listen on port 4433 for HTTP traffic.

C. The router will never accept any HTTP and HTTPS traffic.

D. The router will listen to HTTP and HTTP traffic on port 4433.

View Answer

Question No: 5

A network engineer is configuring a solution to allow failover of HSRP nodes during maintenance windows, as an alternative to powering down the active router and letting the network respond accordingly. Which action will allow for manual switching of HSRP nodes?

A. Track the up/down state of a loopback interface and shut down this interface during maintenance.

B. Adjust the HSRP priority without the use of preemption.

C. Disable and enable all active interfaces on the active HSRP node.

D. Enable HSRPv2 under global configuration, which allows for maintenance mode.

View Answer

Question No: 6

Which routing protocol will continue to receive and process routing updates from neighbors after the passive interface router configuration command is entered?

A. EIGRP

B. RIP

C. OSPF

D. IS-IS

View Answer

Question No: 7

Refer to the exhibit.

The excerpt was taken from the routing table of router SATX. Which option ensures that routes from 51.51.51.1 are preferred over routes from 52.52.52.2?

A. SATX(config-router)#distance 90 51.51.51.1 0.0.0.0

B. SATX(config-router)#distance 89.52.52.52.2 0.0.0.0

C. SATX(config-router)#distance 90.52.52.52.2 0.0.0.0

D. SATX(config-router)#administrative distance 91 51.51.51 0.0.0.0

E. SATX(config-router)#distance 89 51.51.51.1 0.0.0.0

F. SATX(config-router)#administrative distance 91 52.52.52.2 0.0.0.0

View Answer

Question No: 8

Exhibit:

=================

AS65000 (R1)u2014(R2)u2013 (R3)

| |

| |

(R4) (R5)

| |

10.1.0.0/16 10.2.0.0/16

AS 65001 AS65002 Second | should be between R3 and R5

==================

Refer to exhibit. If the IGP in AS65000 is RIPv2, which networks are displayed when you enter show ip route on router R2?

A. VLSM subnts in 10.0.0.0/16 and the major network 10.2.0.0/16 only

B. VLSM subnets in 10.0.0.0/16 and the major network 10.2.0.0/16 only

C. VLSM subnets in 10.0.0.0/16 only

D. major networks 10.1.0.0/16 and 10.2.0.0/16 only

E. VLSM subnets in 10.0.0.0/16 and the major networks 10.1.0.0/16 10.2.0.0/16

View Answer

Question No: 9

What are two limitations when in use of NPTv6 for IPV6 vs IPV6 Address translation?

A. stateful address translation

B. a limit of 32 1-to-1 translations

C. lack of overloading functionality

D. identify all interfaces NAT inside or outside

E. 1-to-1 prefix rewrite

F. mismatched prefix allocations

View Answer

Question No: 10

What is the purpose of the autonomous-system {autonomous-system-number} command?

A. It sets the EIGRP autonomous system number in a VRF.

B. It sets the BGP autonomous system number in a VRF.

C. It sets the global EIGRP autonomous system number.

D. It sets the global BGP autonomous system number.

View Answer

Question No: 11

Refer to Exhibit:

Which statement about the configuration on the Cisco router is true?

A. The router sends only NTP traffic, using the loopback interface, and it disables eth0/0 from sending NTP traffic.

B. Eth0/0 sends NTP traffic on behalf of the loopback interface

C. The router sends only NTP traffic, using the eth0/0 interface, and it disables loopback0 from sending NTP traffic.

D. The router never sends NTP traffic, as using the loopback interface for NTP traffic is not supported on IOS routers.

View Answer

Question No: 12

A network engineer executes the show ip flow export command. Which line in the output indicates that the send queue is full and export packets are not being sent?

A. output drops

B. enqueuing for the RP

C. fragmentation failures

D. adjacency issues

View Answer