The Abreast of the times Guide To 300-115 vce

Q1. A network engineer has just deployed a non-Cisco device in the network and wants to get information about it from a connected device. Cisco Discovery Protocol is not supported, so the open standard protocol must be configured. Which protocol does the network engineer configure on both devices to accomplish this?

A. IRDP

B. LLDP

C. NDP

D. LLTD

View Answer

Q2. Refer to the exhibit.

The network switches for two companies have been connected and manually configured for the required VLANs, but users in company A are not able to access network resources in company B when DTP is enabled. Which action resolves this problem?

A. Delete vlan.dat and ensure that the switch with lowest MAC address is the VTP server.

B. Disable DTP and document the VTP domain mismatch.

C. Manually force trunking with switchport mode trunk on both switches.

D. Enable the company B switch with the vtp mode server command.

View Answer

Q3. What does the command vlan dot1q tag native accomplish when configured under global

configuration?

A. All frames within the native VLAN are tagged, except when the native VLAN is set to 1.

B. It allows control traffic to pass using the non-default VLAN.

C. It removes the 4-byte dot1q tag from every frame that traverses the trunk interface(s).

D. Control traffic is tagged.

View Answer

Q4. Which option lists the information that is contained in a Cisco Discovery Protocol advertisement?

A. native VLAN IDs, port-duplex, hardware platform

B. native VLAN IDs, port-duplex, memory errors

C. native VLAN IDs, memory errors, hardware platform

D. port-duplex, hardware platform, memory errors

View Answer

Q5. Refer to the exhibit.

What is the result of the configuration?

A. The EtherChannels would not form because the load-balancing method must match on the devices.

B. The EtherChannels would form and function properly even though the load-balancing and EtherChannel modes do not match.

C. The EtherChannels would form, but network loops would occur because the load- balancing methods do not match.

D. The EtherChannels would form and both devices would use the dst-ip load-balancing method because Switch1 is configured with EtherChannel mode active.

View Answer

Q6. Which technique automatically limits VLAN traffic to only the switches that require it?

A. access lists

B. DTP in nonegotiate

C. VTP pruning

D. PBR

View Answer

Q7. A network is running VTPv2. After verifying all VTP settings, the network engineer notices that the new switch is not receiving the list of VLANs from the server. Which action resolves this problem?

A. Reload the new switch.

B. Restart the VTP process on the new switch.

C. Reload the VTP server.

D. Verify connected trunk ports.

View Answer

Q8. An access switch has been configured with an EtherChannel port. After configuring SPAN to monitor this port, the network administrator notices that not all traffic is being replicated to the management server. What is a cause for this issue?

A. VLAN filters are required to ensure traffic mirrors effectively.

B. SPAN encapsulation replication must be enabled to capture EtherChannel destination traffic.

C. The port channel can be used as a SPAN source, but not a destination.

D. RSPAN must be used to capture EtherChannel bidirectional traffic.

View Answer

Q9. What effect does the mac address-table aging-time 180 command have on the MAC address-table?

A. This is how long a dynamic MAC address will remain in the CAM table.

B. The MAC address-table will be flushed every 3 minutes.

C. The default timeout period will be 360 seconds.

D. ARP requests will be processed less frequently by the switch.

E. The MAC address-table will hold addresses 180 seconds longer than the default of 10 minutes.

View Answer

Q10. Which command correctly configures standby tracking for group 1 using the default decrement priority value?

A. standby 1 track 100

B. standby 1 track 100 decrement 1

C. standby 1 track 100 decrement 5

D. standby 1 track 100 decrement 20

View Answer