All About Top Quality 300-115 practice test

Q1. after configuring new data VLANs 1020 through 1030 on the VTP server, a network engineer notices that none of the VTP clients are receiving the updates. What is the problem?

A. The VTP server must be reloaded.

B. The VTP version number must be set to version 3.

C. After each update to the VTP server, it takes up to 4 hours propagate.

D. VTP must be stopped and restarted on the server.

E. Another switch in the domain has a higher revision number than the server.

View Answer

Q2. which statement about the use of PAgP link aggregation on a Cisco switch that is running Cisco IOS Software is true?

A. PAgP modes are off, auto, desirable, and on. Only the combinations auto-desirable, desirable-desirable, and on-on allow the formation of a channel.

B. PAgP modes are active, desirable, and on. Only the combinations active-desirable, desirable-desirable, and on-on allow the formation of a channel.

C. PAgP modes are active, desirable, and on. Only the combinations active-active, desirable-desirable, and on-on allow the formation of a channel.

D. PAgP modes are off, active, desirable, and on. Only the combinations auto-auto, desirable-desirable, and on-on allow the formation of a channel.

View Answer

Q3. What is the maximum number of virtual MAC addresses that GLBP allows per group?

A. 2

B. 4

C. 6

D. 8

View Answer

Q4. Refer to the exhibit.

Which statement about switch S1 is true?

A. Physical port Fa0/13, Fa0/14, and Fa0/15 successfully formed a Layer 2 port-channel interface using an open standard protocol.

B. Logical port Fa0/13, Fa0/14, and Fa0/15 successfully formed a Layer 2 physical port- channel interface using a Cisco proprietary protocol.

C. Physical port Fa0/13, Fa0/14, and Fa0/15 successfully formed a Layer 3 port-channel interface using a Cisco proprietary protocol.

D. Logical port Fa0/13, Fa0/14, and Fa0/15 successfully formed a Layer 3 physical port- channel interface using an open standard protocol.

View Answer

Q5. Several new switches have been added to the existing network as VTP clients. All of the new switches have been configured with the same VTP domain, password, and version. However, VLANs are not passing from the VTP server (existing network) to the VTP clients. What must be done to fix this?

A. Remove the VTP domain name from all switches with "null" and then replace it with the new domain name.

B. Configure a different native VLAN on all new switches that are configured as VTP clients.

C. Provision one of the new switches to be the VTP server and duplicate information from the existing network.

D. Ensure that all switch interconnects are configured as trunks to allow VTP information to be transferred.

View Answer

Q6. A network engineer has just deployed a non-Cisco device in the network and wants to get information about it from a connected device. Cisco Discovery Protocol is not supported, so the open standard protocol must be configured. Which protocol does the network engineer configure on both devices to accomplish this?

A. IRDP

B. LLDP

C. NDP

D. LLTD

View Answer

Q7. For security reasons, the IT manager has prohibited users from dynamically establishing trunks with their associated upstream switch. Which two actions can prevent interface trunking? (Choose two.)

A. Configure trunk and access interfaces manually.

B. Disable DTP on a per interface basis.

C. Apply BPDU guard and BPDU filter.

D. Enable switchport block on access ports.

View Answer

Q8. What is the maximum number of switches that can be stacked using Cisco StackWise?

A. 4

B. 5

C. 8

D. 9

E. 10

F. 13

View Answer