The Refresh Guide To 352-001 exam dumps

Q1. Your company is designing a service provider network management solution in which customers are billed for 95th percentile network utilization. The service provider requires that an IETF standard be utilized to collect the data. Which method should be used to collect the data? 

A. IPFIX 

B. NETFLOW 

C. RMON 

D. IPFLOW 

E. NBAR 

View Answer

Q2. Which design concern should be accounted for in all Layer 3 virtualization technologies? 

A. Layer 3 redundancy 

B. packet sizing 

C. application usage 

D. Layer 3 stability 

View Answer

Q3. ACME Corporation is integrating IPv6 into their network, which relies heavily on multicast distribution of data. Which two IPv6 integration technologies support IPv6 multicast? (Choose two.) 

A. 6VPE 

B. 6PE 

C. dual stack 

D. ISATAP 

E. 6to4 

F. IPv6INIP 

View Answer

Q4. You are designing a multisite VPN solution for a customer and you are concerned with the additional overhead of point-to-point tunnels and the associated overlay routing with DMVPN. How does a GDOI-based VPN eliminate the additional tunnel and routing overhead found in DMVPN? 

A. The GDOI-based VPN requires overlaying a secondary routing infrastructure through the tunnels. 

B. In a GDOI-based VPN, all group members share a common security association. 

C. The GDOI-based VPN requires the provisioning of a complex connectivity mesh. 

D. The GDOI-based VPN leverages the routing protocol to find its peer for tunnel setup. 

View Answer

Q5. You are designing an IPv4 any source multicast redundancy solution. Which technology ensures the quickest RP convergence? 

A. Auto-RP 

B. Embedded RP 

C. bootstrap router 

D. MSDP anycast RP 

View Answer

Q6. Refer to the exhibit. 

In this BGP design, what is the next hop for 10.1.1.0/24 on R8 and R7? 

A. The next hop for 10.1.1.0/24 on R7 is R8 and the next hop for R8 is R7. 

B. The next hop for 10.1.1.0/24 on R7 is R5 and the next hop for R8 is R6. 

C. The next hop for 10.1.1.0/24 on R7 is R6 and the next hop for R8 is R5. 

D. The next hop for 10.1.1.0/24 on R7 is R3 and the next hop for R8 is R4. 

View Answer

Q7. You have designed a network to support two offices connected by a T1. Your router serial interfaces will be configured with encapsulation PPP. What will happen to your EIGRP neighbors if there is an LCP failure once your network is implemented? 

A. Your neighbors will drop after the EIGRP timers expire. 

B. Your neighbors will stay up because the link has not gone down. 

C. Your neighbors will drop immediately. 

D. Your neighbors will drop and EIGRP will begin the query process. 

View Answer

Q8. A company wants a design that would support OSPF through a service provider ATM network. Which two OSPF network types should the designer use to establish OSPF neighborship between OSPF routers through the ATM network? (Choose two.) 

A. A broadcast network will always work through ATM networks. 

B. A broadcast network will work when the broadcast support is explicitly configured at the ATM network. 

C. Explicit neighbor statements are required when a nonbroadcast network is configured. 

D. Explicit neighbor statements are required when a point-to-multipoint network is configured. 

E. A nonbroadcast network does not require DR selection. 

View Answer

Q9. When designing a network, which two security features should be added to the design to protect hosts from potential IPv6 neighbor discovery denial of service attacks at the access layer? (Choose two.) 

A. SEND 

B. RA Guard 

C. IKEv2 

D. IPsec 

E. DMVPNv6 

View Answer

Q10. Refer to the exhibit. 

This Layer 2 ring has 10 VLANs with 1000 MAC addresses in each VLAN. Which protocol or mechanism provides the shortest traffic outage if the link marked with "X" fails? 

A. PVRST 

B. REP 

C. MST 

D. G.8031 

E. BFD 

View Answer