Ucertify 642-035 Questions are updated and all 642-035 answers are verified by experts. Once you have completely prepared with our 642-035 exam prep kits you will be ready for the real 642-035 exam without a problem. We have Far out Cisco 642-035 dumps study guide. PASSED 642-035 First attempt! Here What I Did.


2026 New 642-035 Exam Dumps with PDF and VCE Free: https://www.surepassexam.com/642-035-exam-dumps.html

Q1. You are attempting to install Microsoft Server 2008 R2 on a Fibre Channel LUN, but the installer does not see the LUN. You have used F6 to load the appropriate SCSI driver. What should your first troubleshooting step be? 

A. Email the SAN administrator to validate that your LUN is defined. 

B. Check the configuration of the vHBA in the service profile. 

C. Validate that the boot order is correct. 

D. Validate zoning on the Fibre Channel switch. 

E. Validate that the Fibre Channel uplink from the fabric interconnect is up. 

Answer: B 

Q2. A Cisco UCS chassis has two ports on I/O Module 1 connected to Fabric Interconnect A, and two ports on I/O Module 2 connected to Fabric Interconnect B. The I/O modules are connected to ports 1 and 2 on their respective fabric interconnects, and end host mode is configured. After a link failure occurs on port 1 of I/O Module 1, what happens to the traffic that was pinned to that link? 

A. The traffic fails until the link issue is resolved. 

B. The traffic is repinned to I/O Module 2 link 1, which is connected to Fabric Interconnect 

C. The traffic is repinned to the remaining link between I/O Module 1 and Fabric Interconnect A. 

D. The traffic is repinned automatically to Fabric Interconnect B. 

Answer: C 

Q3. A customer is configuring VSANs in a Cisco UCS domain. After configuring the VSANs 3840, 3841, and 3842 in FC end-host mode, the customer sees that these VSANs are not operational and that Cisco UCS Manager is raising faults. What is the cause of this problem? 

A. VSANs 3840, 3841, and 3842 should be in the allowed list on the trunk to clear the fault. 

B. VSANs 3840 to 4079 cannot be used in Fibre Channel end-host mode in a Cisco UCS domain. 

C. The fabric interconnect needs to be configured in switching mode and the VSANs need to be allowed on the trunk. 

D. Use the UCS CLI to clear the fault on the VSAN trunk to forward the VSANs with faults. 

Answer: B 

Q4. You successfully install VMware ESXi 5.0 U1 on a Cisco UCS B200 M3 server to a Fibre Channel LUN. When you reboot the server, you see the message "Reboot and Select Proper Boot device or insert Boot Media in selected Boot device and press a key." What are the first two pieces of information you should gather to troubleshoot the boot failure? (Choose two.) 

A. Connect to the NX-OS shell via the CLI and run the show npv flogi-table command. 

B. SSH to the MDS 9124 and run the show flogi database command. 

C. Validate the boot target WWPN and LUN ID in the service profile. 

D. Validate the correct source WWPN in the service profile vHBA definition. 

E. Validate zoning for your WWPN on the Cisco MDS 9124. 

F. Validate that the boot order indicates the vHBA as the first device. 

G. Ensure LUN masking is correctly configured on the storage controller. 

Answer: CF 

Q5. You are installing Microsoft Windows Server 2008 R2 on a Cisco UCS C210 M2 server, and the installer does not see local storage on the LSI MegaRAID SAS 9260-4i controller that is installed. Which statement explains the issue? 

A. The driver is not included in the installer DVD. Press F6 to load the LSI RAID driver from CD or virtual media. 

B. The virtual disk is not created and online. 

C. The LSI 9260-4i is only supported by Red Hat Enterprise Linux and VMware vSphere 

4.0 and later. 

D. The installer DVD for Microsoft Windows Server 2008 R2 did not include the LSI driver until SP2. 

Answer: B 

Q6. Which remote access protocol is used by default to obtain CLI access to a Cisco UCS C-Series standalone server? 

A. Telnet 

B. SSH 

C. HTTP 

D. SSL 

E. SOCKS 

Answer: B 

Q7. What is the correct sequence to export tech support data from the Cisco IMC GUI interface? 

A. Admin tab > Utilities > Export Technical Support to TFTP 

B. Utilities tab > Utilities > Export Technical Support to TFTP 

C. Server tab > Utilities > Export Technical Support to TFTP 

D. Communications tab > Utilities > Export Technical Support to TFTP 

E. Support tab > Utilities > Export Technical Support to TFTP 

F. Help tab > Utilities > Export Technical Support to TFTP 

Answer: A 

Q8. Which statement is true about system event logs? 

A. By default, they require manual clearing. 

B. They report operating system crashes and errors. 

C. They are also referred to as system error logs. 

D. They can only be accessed from Cisco UCS Manager. 

Answer: A 

Q9. How will the Cisco UCS Manager react when all of the FSM tasks fail? 

A. retries for 60 seconds 

B. raises faults and alarms 

C. restarts from the previous known good task 

D. sends an NOC SNMP trap email 

Answer: B 

Q10. For a KVM session to be successful, which two of these need to be done? (Choose two.) 

A. The Cisco IMC IP address needs to be assigned on the Admin tab. 

B. The Cisco IMC IP address needs to be in the same subnet as the management IP. 

C. The Cisco IMC needs to be upgraded to the same version as the UCS Manager. 

D. The server needs to be fully discovered. 

Answer: AD