10 Tips For Up to date 642-035 examcollection

Q1. A customer is trying to boot an operating system that is installed on the eUSB on a Cisco UCS B-Series blade server; however, the boot fails. What is the cause of this failure? 

A. The local disk must be the first device in the boot order. 

B. eUSB is not a supported boot device. 

C. eUSB support is available only on the Cisco UCS C-Series rack server. 

D. eUSB is not the first device in the boot order for the server. 

View Answer

Q2. What should you do when you see faults during the initial setup and discovery process? 

A. Take note and address the faults. 

B. You can safely ignore these faults. 

C. Log them and try to address the first one. 

D. Reboot until the error messages go away. 

View Answer

Q3. Which remote access protocol is used by default to obtain CLI access to a Cisco UCS C-Series standalone server? 

A. Telnet 

B. SSH 

C. HTTP 

D. SSL 

E. SOCKS 

View Answer

Q4. When using the Cisco UCS Manager GUI to troubleshoot a suspected bad memory, which 

logs contain data that are related to the faulty DIMM? 

A. the System Event log and Faults log that are located under the Admin tab 

B. the Events log and Faults log that are located under the Admin tab 

C. the System Event log that is located under the Server tab in the Navigation panel and the Faults log that is located under the Admin tab 

D. the System Event log that is located under the Equipment tab and the Faults log that is located under the Admin tab 

View Answer

Q5. RBAC is a method of restricting access for a particular user on which two of these? (Choose two.) 

A. roles 

B. realm 

C. locales 

D. RADIUS 

E. LDAP 

View Answer

Q6. While attempting to boot a Cisco UCS server from SAN, you are unable to see the LUN. Which of these are causing the problem? (Choose three.) 

A. VHBA template 

B. RAID policy 

C. zoning 

D. LUN ID 

E. vACLs 

F. disjoint fabrics 

View Answer

Q7. You are troubleshooting an FCoE SAN boot issue on a Cisco UCS C240 M3 server with a VIC 1225. Which two of these represent the correct way to bind VSAN 11 to interface vfc5 attached to interface Ethernet 1/5? (Choose two.) 

A. 5548UP(config)# int vfc 5 5548UP(config-if)# bind interface Ethernet1/5 vsan 11 

B. 5548UP(config)# vsan database 5548UP(config-vsan-db)# vsan 11 interface vfc5 

C. 5548UP(config)# interface Ethernet1/5 5548UP(config-if)# bind vsan 11 

D. 5548UP(config)# vsan database 5548UP(config-vsan-db)# bind interface vfc5 vsan 11 

E. 5548UP(config)# vsan database 5548UP(config-vsan-db)# interface vfc5 vsan 11 

F. 5548UP(config)# vsan database 5548UP(config-vsan-db)# interface Ethernet1/5 vsan 11 

View Answer

Q8. As a Cisco UCS administrator, you have a large deployment of C-Series servers. You decide to integrate these into a Cisco UCS Manager environment to simplify management. Which two of these will you need to purchase? (Choose two.) 

A. two fabric interconnects 

B. a dedicated Cisco IMC 

C. two fabric extenders 

D. two I/O modules 

View Answer

Q9. Which two types of ports does end host mode switching have? (Choose two.) 

A. VSS 

B. border 

C. router 

D. server 

E. STP 

F. client 

View Answer

Q10. Which three methods can be used to upgrade the Cisco IMC? (Choose three.) 

A. host firmware package 

B. blade firmware package 

C. controller firmware package 

D. management firmware package 

E. directly on the blade, under the Installed Firmware tab 

F. directly on the blade, under the Blade Firmware tab 

G. directly on the blade, under Inventory > CIMC 

View Answer