What Top Quality 642-035 exam question Is?

Q1. Which four tasks can be performed via Cisco IMC remote access to a Cisco UCS system? (Choose four.) 

A. power cycle the server 

B. deploy an operating system 

C. toggle the locator LED 

D. configure the boot order 

E. view properties and sensors 

F. configure the hypervisor 

G. enable Cisco UCS Manager 

View Answer

Q2. A customer is troubleshooting QoS in a Cisco UCS domain due to high packet drops in the network. The customer has configured the vNIC and associated QoS policy, and changed the MTU from 1000 to 1200. Packet drops still exist. What is the cause of this issue? 

A. The MTU specified here must be greater than the MTU specified in the associated QoS system class. If this MTU value is less than the MTU value in the QoS system class, packets may be dropped during data transmission. 

B. The MTU specified here must be equal to or less than the MTU specified in the associated QoS system class. If this MTU value exceeds the MTU value in the QoS system class, packets may be dropped during data transmission. 

C. The MTU specified here must be less than the MTU specified in the associated QoS system policy. If this MTU value exceeds the MTU value in the QoS system policy, packets may be not be dropped during data transmission. 

D. The MTU must be optimized and should be changed to fc with the CLI command set mtu fc. 

View Answer

Q3. A customer calls in a trouble ticket and explains that after a power failure, the UPS was discovered to be defective and the Cisco UCS C210 M2 server running Windows 2008 R2 went down without proper shutdown. After restarting the server, you discover the RAID 5 array rebuilding parity. Which write-cache settings on the LSI MegaRAID 9260-4i controller explain this symptom? 

A. write back 

B. write through 

C. write back with BBU 

D. no write cache 

E. no hot spare 

View Answer

Q4. On a Cisco UCS B-Series data center environment; how many default roles are there when utilizing RBAC for security restriction? 

A. 1 

B. 5 

C. 10 

D. 15 

E. 20 

View Answer

Q5. Which three Cisco UCS server components can be upgraded via a host firmware package? (Choose three.) 

A. BIOS 

B. Cisco UCS Manager 

C. I/O module 

D. Cisco IMC 

E. fabric interconnect 

F. adapter 

G. board controller 

View Answer

Q6. You are troubleshooting an FCoE boot issue on a Cisco UCS C220 M3 server with a VIC 1225 CNA. Which two pieces of information can you directly infer from the output of the show zone active command below? (Choose two.) 

zone name Server_1-to-Storage vsan 11 

pwwn 50:06:01:60:3b:a0:08:9f [Storage] 

*fcid 0x3b000b [pwwn 20:00:00:25:b5:04:0a:02] [C22_Server] 

A. The storage controller is not logged into the fabric. 

B. The server is not logged into the fabric. 

C. Only the storage controller is logged into the fabric. 

D. Only the server is logged into the fabric. 

E. The initiator and target cannot communicate because they are on the wrong VSAN. 

F. The WWPN of the storage controller is mistyped. 

G. The initiator and target cannot communicate because the zone name does not match the server name (C22_Server). 

View Answer

Q7. UCS-A# scope eth-uplink UCS-A /eth-uplink 

# scope fabric a UCS-A /eth-uplink/fabric 

# scope interface 2 3 UCS-A /eth-uplink/fabric/interface 

# create mon-src Monitor23 UCS-A /eth-uplink/fabric/interface/mon-src* 

# set direction receive UCS-A /eth-uplink/fabric/interface/mon-src* # commit-buffer 

What does the command scope interface 2 3 in the above CLI command sequence do on a Cisco UCS blade server? 

A. enters the interface command mode for the specified uplink port 

B. enters the interface command mode for the specified Fabric A 

C. enters the interface command mode for the specified Fabric B 

D. enters slot 3 port 2 specified uplink port 

View Answer

Q8. When a service profile is disassociated from a server, what happens to the identity and connectivity information for the server? 

A. It is cleared and set to the default that was setup initially by the first configuration. 

B. It is maintained and can be reused. 

C. It is reset to factory defaults. 

D. It uses master service profile parameters. 

E. It takes parameters of other servers in the service profile. 

View Answer

Q9. During a password recovery of a Cisco UCS system in a cluster configuration, what happens to blade traffic? 

A. There is no interruption to traffic, as the fabrics go down one at a time. 

B. Traffic stops flowing until the process is complete. 

C. There is no interruption to traffic because both fabrics stay up the whole time. 

D. Traffic will continue to flow, but at a limited rate until the process is complete. 

View Answer

Q10. A customer would like to create an Ethernet traffic monitoring session on a Cisco UCS server to troubleshoot network connectivity. The customer has entered the following commands via CLI: 

UCS-A# scope eth-traffic-mon UCS-A /eth-traffic-mon # scope fabric a UCS-A /eth-traffic-mon/fabric # create eth-mon-session EthMonitor33 UCS-A /eth-traffic-mon/fabric/eth-mon-session* # create dest-interface 2 12 UCS-A /eth-traffic-mon/fabric/eth-mon-session/dest-interface* # set speed 20gbps UCS-A /eth-traffic-mon/fabric/eth-mon-session/dest-interface* # commit-buffer UCS-A /eth-traffic-mon/fabric/eth-mon-session/dest-interface # 

Which outcome will this command sequence produce? 

A. It will create an Ethernet traffic monitoring session to copy and forward traffic to the destination port at slot 2, port 12, will set the admin speed to 20 Gb/s, and will commit the transaction. 

B. It will create an Ethernet traffic monitoring session to copy and forward traffic to the destination port at slot 2, port 33, will set the admin speed to 20 Gb/s, and will commit the transaction. 

C. It will create an Ethernet traffic monitoring session to copy and forward traffic to the destination port at slot 33, port 12, will set the admin speed to 20 Gb/s, and will commit the transaction. 

D. It will create an Ethernet traffic monitoring session to copy and forward traffic to the destination port at slot 2, port 12, will set the admin speed to 10 Gb/s, and will commit the transaction. 

View Answer