Want to know Examcollection 642-035 Exam practice test features? Want to lear more about Cisco Troubleshooting Cisco Data Center Unified Computing certification experience? Study Precise Cisco 642-035 answers to Renewal 642-035 questions at Examcollection. Gat a success with an absolute guarantee to pass Cisco 642-035 (Troubleshooting Cisco Data Center Unified Computing) test on your first attempt.


2026 New 642-035 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/642-035/

Q1. At any given time, each server can be associated with how many service profiles? 

A. 1 

B. 2 

C. 5 

D. 10 

E. unlimited 

Answer: A 

Q2. What should you do when you see faults during the initial setup and discovery process? 

A. Take note and address the faults. 

B. You can safely ignore these faults. 

C. Log them and try to address the first one. 

D. Reboot until the error messages go away. 

Answer: B 

Q3. A local storage installation of ESX on a Cisco UCS C-Series server has failed due to local storage issues. What is the cause of the problem? 

A. LSI drivers are not bundled with ESX. 

B. The hard drive has a 1-TB partition size. 

C. The server only has an onboard controller, while ESX requires an LSI RAID controller card. 

D. ESX is not supported on Cisco UCS C-series servers. 

Answer: C 

Q4. A customer calls in a trouble ticket and explains that after a power failure, the UPS was discovered to be defective and the Cisco UCS C210 M2 server running Windows 2008 R2 went down without proper shutdown. After restarting the server, you discover the RAID 5 array rebuilding parity. Which write-cache settings on the LSI MegaRAID 9260-4i controller explain this symptom? 

A. write back 

B. write through 

C. write back with BBU 

D. no write cache 

E. no hot spare 

Answer: A 

Q5. On a Cisco UCS B-Series data center environment; how many default roles are there when utilizing RBAC for security restriction? 

A. 1 

B. 5 

C. 10 

D. 15 

E. 20 

Answer: C 

Q6. Which remote access protocol is used by default to obtain CLI access to a Cisco UCS C-Series standalone server? 

A. Telnet 

B. SSH 

C. HTTP 

D. SSL 

E. SOCKS 

Answer: B 

Q7. A customer is trying to boot an operating system that is installed on the eUSB on a Cisco UCS B-Series blade server; however, the boot fails. What is the cause of this failure? 

A. The local disk must be the first device in the boot order. 

B. eUSB is not a supported boot device. 

C. eUSB support is available only on the Cisco UCS C-Series rack server. 

D. eUSB is not the first device in the boot order for the server. 

Answer: D 

Q8. UCS-A# scope eth-uplink UCS-A /eth-uplink 

# scope fabric a UCS-A /eth-uplink/fabric 

# scope interface 2 3 UCS-A /eth-uplink/fabric/interface 

# create mon-src Monitor23 UCS-A /eth-uplink/fabric/interface/mon-src* 

# set direction receive UCS-A /eth-uplink/fabric/interface/mon-src* # commit-buffer 

What does the command scope interface 2 3 in the above CLI command sequence do on a Cisco UCS blade server? 

A. enters the interface command mode for the specified uplink port 

B. enters the interface command mode for the specified Fabric A 

C. enters the interface command mode for the specified Fabric B 

D. enters slot 3 port 2 specified uplink port 

Answer: A 

Q9. You are troubleshooting an FCoE boot issue on a Cisco UCS C220 M3 server with a VIC 1225 CNA. Which two pieces of information can you directly infer from the output of the show zone active command below? (Choose two.) 

zone name Server_1-to-Storage vsan 11 

pwwn 50:06:01:60:3b:a0:08:9f [Storage] 

*fcid 0x3b000b [pwwn 20:00:00:25:b5:04:0a:02] [C22_Server] 

A. The storage controller is not logged into the fabric. 

B. The server is not logged into the fabric. 

C. Only the storage controller is logged into the fabric. 

D. Only the server is logged into the fabric. 

E. The initiator and target cannot communicate because they are on the wrong VSAN. 

F. The WWPN of the storage controller is mistyped. 

G. The initiator and target cannot communicate because the zone name does not match the server name (C22_Server). 

Answer: AD 

Q10. In new Cisco UCS release 2.0 installations, what are the default VLAN IDs? 

A. Ethernet VLAN default ID is 4048, FCOE default VLAN ID 4048 

B. Ethernet VLAN default ID is 1, FCOE default VLAN ID is 3968 

C. Ethernet VLAN default ID is 1, FCOE default VLAN ID is 2 

D. Ethernet VLAN default ID is 2, FCOE default VLAN ID is 4047 

E. Ethernet VLAN default ID is 1, FCOE default VLAN ID is 4048 

Answer: E