It is impossible to pass Cisco 642-997 exam without any help in the short term. Come to Exambible soon and find the most advanced, correct and guaranteed Cisco 642-997 practice questions. You will get a surprising result by our Far out Implementing Cisco Data Center Unified Fabric (DCUFI) v5.0 practice guides.


2026 New 642-997 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/642-997/

Q1. Which statement about Cisco FabricPath is true? 

A. It is the best solution for interconnecting multiple data centers. 

B. It optimizes STP throughout the Layer 2 network. 

C. It is a simplified extension of Layer 3 networks across a single data center. 

D. The Cisco FabricPath domain appears as a single STP bridge, where each edge port uses the same MAC address. 

Answer: D 

Q2. Refer to the exhibit. 

 

What is the consequence of configuring peer-gateway on the two vPC peers N7K-1 and N7K-2? 

A. Nothing, this is the standard vPC configuration to make the feature work. 

B. The downstream device detects only one of the vPC peers as its gateway. 

C. The downstream device can use DMAC of N7K-1 on the link to N7K-2, and N7K-2 forwards the packet. 

D. This configuration enables the downstream device to use DHCP to obtain its default gateway. 

Answer: C 

Q3. What is an Overlay Transport Virtualization extended VLAN? 

A. the VLAN used to locate other AEDs 

B. the VLAN used to access the overlay network by the join interface 

C. the user VLAN that exists in multiple sites 

D. the VLAN that must contain the overlay interface 

Answer: C 

Q4.  

What is effect of the command fabricpath load-balance unicast Iayer3"? 

A. It configures F2 VDC FabricPath unicast load balancing 

B. The command automatically load balances broadcast traffic 

C. It configures F1/MI VDC FabricPath unicast load balancing 

D. It configures M1 VDC FabricPath unicast load balancing 

Answer: C 

Q5. Which option is a restriction of the unified ports on the Cisco UCS 6200 Series Fabric Interconnect when connecting to the unified fabric network? 

A. Direct FC connections are not supported to Cisco MDS switches 

B. The FCoE or Fibre Channel port allocations must be contiguous on the 6200. 

C. 10-G Fibre Channel ports only use SFP+ interfaces. 

D. vPC is not supported on the Ethernet ports. 

Answer: B 

Q6.  

Ethernet interface 1/5 on Cisco Nexus 5548 is connected to Cisco UCS C220 rack server. What is the status of Ethernet 1/5 interface for FCoE functionality? 

A. Interface reset on Ethernet 1/5 is preventing the FCoE connection from coming up 

B. MTU size of 1500 on Ethernet interface 1/5 needs to be changed for FCoE to come UP 

C. Cisco Nexus 5548 needs a layer 3 daughter card for FCoE to come UP on the Ethernet interface 1/5 

D. Ethernet interface 1/5 is operational for FCoE and the status is UP 

Answer: D 

Q7. Which statement about the Layer 3 card on the Cisco Nexus 5500 Series Switch is true? 

A. BGP support is not provided, but RIP, EIGRP, and OSPF support is provided. 

B. Up to two 4-port cards are supported with up to 160 Gb/s of Layer 3 forwarding capability. 

C. Up to 16 FEX connections are supported. 

D. Port channels cannot be configured as Layer 3 interfaces. 

Answer: C 

Q8.  

On a Cisco Nexus7000 switches what is true regarding Cisco FabrciPath requirements? 

A. Ensure that you have installed the Enhanced Layer 2 license and that you have installed an F Series module 

B. Ensure that you have installed the Enhanced Layer 2 license and that you have installed an M Series module 

C. Ensure that you have installed the Enhanced Layer 3 license and that you have installed an M Series module 

D. Ensure that you have installed the Scalable Feature License license and that you have installed an F Series module 

Answer: A