Want to know Examcollection 200-601 Exam practice test features? Want to lear more about Cisco Managing Industrial Networking for Manufacturing with Cisco Technologies certification experience? Study Breathing Cisco 200-601 answers to Improved 200-601 questions at Examcollection. Gat a success with an absolute guarantee to pass Cisco 200-601 (Managing Industrial Networking for Manufacturing with Cisco Technologies) test on your first attempt.


2026 New 200-601 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-601/

Q1. Which statement is true regarding ProfiSAFE? 

A. ProfiSAFE traffic must be carried on a network that is physically.separated from automation traffic 

B. ProfiSAFE relies on the error detection mechanisms of Ethernet and TCP/IP to determine if there are network errors 

C. ProfiSAFE can be used in safety applications up to Safety Integrity Level 3 (SIL3) 

D. ProfiSAFE is only used by ProfiBUS PA and ProfiBUS DA devices 

Answer: C 

Q2. Refer to the exhibit. 

An expansion project added an E-Tap and Device Level Ring to interface FastEthernet1/1 of L2SW1. The administrator has looked at the logs of L2SW1 and found that FastEthernet1/1 was in an error-disabled state.Using command line access on L2SW1, the.administrator issued the following commands in configuration mode: 

L2SW1(config)# interface FastEthernet 1/1 L2SW1(config-if)# shutdown L2SW1(config-if)# no shutdown 

The administrator checked the logs of L2SW1 and found the following: 

Mar 30 02:23:17.588: %PM-4-ERR_DISABLE: bpduguard error detected on Fa1/1, putting Fa1/1 in err-disable state 

The administrator checked the software configuration of the switch port and found the following: 

interface FastEthernet1/1 switchport access vlan 310 switchport mode access speed 100 duplex full no mdix auto spanning-tree portfast spanning-tree bpduguard enable 

Why has the port gone error-disabled? 

A. interface FastEthernet1/1 is configured as an access port on the wrong VLAN. 

B. There is a duplex mismatch between interface FastEthernet1/1 and the E-Tap. 

C. The E-Tap is not configured as a ring supervisor causing a loop on interface FastEthernet1/1. 

D. The E-Tap is configured at 10Mbps and the switch port is configured at 100Mbps. 

E. Automatic MDI Crossover detection is disabled. 

Answer: C 

Q3. What security component can be deployed to increase the defense in depth and specifically can be positioned against 'man-in-the-middle' attack? 

A. Deploy 802.1AE 

B. Deploy 802.1X 

C. Deploy 802.1Q 

D. Deploy 802.1AX 

Answer: A 

Q4. Refer to the exhibit. 

You are required to implement traffic segmentation in the network. See the table for relevant device details: 

L2SW4, L2SW5, and L2SW6.are connected to L3SW1.with 802.1Q trunks.with VLAN.191 and VLAN 398 allowed on the trunk. 

You have the following information from L3SW1: L3SW1# show run interfaces 

interface Vlan1 no ip address shutdown ! interface Vlan2 ip address 10.2.2.2 255.255.255.248 ! interface Vlan191 ip address 10.10.27.126 255.255.255.192 ! interface Vlan200 ip address 10.20.20.1 255.255.255.248 ! interface Vlan398 ip address 10.15.153.1 255.255.255.0 

L3SW1# show ip route 

*** Output Omitted *** 10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks 

C.10.2.2.1/29 is directly connected, Vlan2 

C.10.10.27.64/26 is directly connected, Vlan191 

C.10.15.153.0/24 is directly connected, Vlan398 

C.10.20.20.0/29 is directly connected, Vlan200 

S.10.200.200.0/24 [1/0] via 10.20.20.2 

S* 0.0.0.0/0 [1/0] via 10.2.2.1 

You are required to implement a configuration that will meet the following connectivity requirements:

.. The Administrator's Station must have full access to PanelView 

. PanelView should have limited access, based on specific TCP ports, to PLC#1 and I/O#1

.. The Administrator's Station should have no access to PLC#1 and I/O#1

.. PLC#1 and I/O#1 should be able to communicate with each other on any port 

Which action will allow you to meet the connectivity requirements? 

A. Put interface VLAN 191 and interface VLAN 398 into different Virtual Routing and Forwarding (VRF) instances on L3SW1 

B. Deploy an inbound ACL on interface VLAN 191 to control the traffic from the Administrator's Station and PanelView to PLC#1 and I/O#1 

C. No change is required, the traffic is already limited appropriately by the VLAN segmentation 

D. Implement an ACL on Firewall1 to control the traffic flow between VLAN 191 and VLAN 398 

Answer: B 

Q5. Refer to the exhibit. The Robot Cell is in a bottling plant. This cell environment needs to consider high flex, EMI, and possible exposure to moisture. Which physical media components need to be considered to prevent network degradation or interruptions? 

A. Stranded, shielded wire with an industrial jacket and M12 connectors 

B. Solid, unshielded commercial jacket wire, and M12 connectors 

C. Stranded, unshielded wire with an industrial jacket, and commercial grade RJ45 connectors 

D. Solid, shielded wire with commercial grade jacket, and commercial grade RJ45 connectors 

Answer: A 

Q6. Your supervisor calls you and tells you that one of the Stratix 5700 switches is not assigning all CIP explicit messages to the proper QoS queue. The switch was deployed with the ab-global macro and CIP explicit messages were previously being assigned to the proper QoS queue. You suspect the access-lists associated with the ab-global macro have been changed. Look at the following access list from the switch configuration: 

access-list 101 permit udp any eq 2222 any dscp 55 

access-list 102 permit udp any eq 2222 any dscp 47 

access-list 103 permit udp any eq 2222 any dscp 43 

access-list 104 permit udp any eq 2222 any 

access-list 105 permit udp any eq 44818 any 

access-list 105 permit tcp any eq 44816 any 

What needs to be done to fix the above access list? 

A. Access list 105 should reference udp port 44816 

B. Access lists 101-104 should reference udp port 2212 

C. Access list 105 should reference tcp port 44818 

D. Access list 104 should be a deny access list rather than a permit access list 

Answer: C 

Q7. Which option best describes the ProfiNET Discovery and Configuration Protocol (DCP)? 

A. Can be used to override both static and dynamically (DHCP/BOOTP) assigned IP addresses 

B. Cannot be used to reset a device to factory defaults 

C. Is only supported in Conformance Class B and C devices 

D. Uses the ProfiNET-IRT communication class 

Answer: A 

Q8. What percentage of an I/O connection would you set the RPI in order to ensure the application has the most current data? 

A. RPI at 50% of IO rate 

B. RPI at 25% of IO rate 

C. PI to 25% of PAC scan rate 

D. Set RPI to 50% of PAC scan rate 

Answer: A 

Q9. ProfiNET has been disabled on a Cisco Industrial Ethernet switch. Which CLI command.will correctly enable ProfiNET on the switch? 

A. switch(config)#profinet 

B. switch(config-if)#switchport profinet vlan 10 

C. switch(config)#vlan 10 profinet 

D. switch#enable profinet 

Answer: A 

Q10. What can be done to increase the security in depth in an industrial zone? 

A. Add additional disk storage to the IDS server 

B. Add specific SCADA signatures to the IDS server 

C. Create a high availability solution for the IDS server 

D. Place a 'data diode' in front of the IDS server 

Answer: B