10 Tips For Up to date 300-075 practice test

Q1. Which minimum configuration is needed for the SAF Internal Client to register with this SAF Forwarder? 

A. router eigrp SAF!service-family ipv4 autonomous-system 1!topology baseexit-sf-topologyexit-service-family!voice service safprofile trunk-route 1session protocol sip interface Loopbackl transport tcp port 5060i 

B. router eigrp SAF!service-family ipv4 autonomous-system 1!topology baseexit-sf-topologyexit-service-family!voice service safprofile trunk-route 1session protocol sip interface Loopbackl transport tcp port 5060!profile dn-block 1 alias-prefix 1972555pattern 1 type extension 4xxx!profile callcontrol 1dn-servicetrunk-route 1dn-block 1dn-block 2i 

C. router eigrp SAF!service-family ipv4 autonomous-system 1!topology baseexit-sf-topologyexit-service-family!voice service safprofile trunk-route 1session protocol sip interface Loopbackl transport tcp port 5060!profile dn-block 1 alias-prefix 1972555pattern 1 type extension 4xxx!profile callcontrol 1dn-servicetrunk-route 1dn-block 1dn-block 2!channel 1 vrouter SAF asystem 1subscribe callcontrol wildcardedpublish callcontrol 1i 

D. router eigrp SAF!service-family ipv4 autonomous-system 1!topology baseexit-sf-topologyexit-service-family!voice service saf!channel 1 vrouter SAF asystem 1 

E. router eigrp SAF!service-family ipv4 autonomous-system 1!topology base exit-sf-topologyexit-service-family i 

View Answer

Q2. What is the difference between an MGCP gateway and a SIP gateway? 

A. An MGCP gateway that dial peers be configured before PSTN calls can be placed and received. The SIP gateway requires no dial peers. 

B. An MGCP gateway can be added in Cisco Unified Communications Manager under the Gateway Type field using the gateway model. The SIP gateway can connect to Cisco Unified Communications Manager only through a SIP trunk. 

C. A SIP gateway requires a call agent for PSTN calls to be placed and received. An MGCP gateway does not require a call agent for PSTN calls to be placed and received. 

D. An MGCP gateway can register with Cisco Unified Communications Manager. A SIP gateway will show status of "Unknown". 

E. The SIP gateway must be configured in Cisco Unified Communications Manager using a valid IP address on the gateway. The MGCP gateway must be configured in Cisco Unified 

Communications Manager using the domain name. 

View Answer

Q3. Which configuration command disables the secondary dial tone on the branch office ISR for users calling from the PSTN into the branch office during a WAN failure? 

A. direct-inward-dial 

B. voice translation-rule 

C. incoming called-number 

D. application 

View Answer

Q4. When implementing a dial plan for multisite deployments, what must be present for SRST to work successfully? 

A. dial peers that address all sites in the multisite cluster 

B. translation patterns that apply to the local PSTN for each gateway 

C. incoming and outgoing COR lists 

D. configuration of the gateway as an MGCP gateway 

View Answer

Q5. Which two actions ensure that the call load from Cisco TelePresence Video Communication Server to a Cisco Unified Communications Manager cluster is shared across Unified CM nodes? (Choose two.) 

A. Create a neighbor zone in VCS with the Unified CM nodes listed as location peer addresses. 

B. Create a single traversal client zone in VCS with the Unified CM nodes listed as location peer addresses. 

C. Create one neighbor zone in VCS for each Unified CM node. 

D. Create a VCS DNS zone and configure one DNS SRV record per Unified CM node. 

E. In VCS set Unified Communications mode to Mobile and remote access and configure each Unified CM node. 

View Answer

Q6. Which remote-site redundancy technology fails over to POTS dial peers from the Cisco Unified Communications Manager dial plan during a WAN failure? 

A. MGCP fallback 

B. H.323 fallback 

C. SCCP fallback 

D. SIP fallback 

View Answer

Q7. What is the difference between an H.323 gateway and a SIP gateway? 

A. An H.323 gateway requires that dial peers be configured before PSTN calls can be placed and received. The SIP gateway requires no dial peers. 

B. The H.323 gateway can be added in Cisco Unified Communications Manager under gateway type as H.323 Gateway. The SIP gateway can connect to Cisco Unified Communications Manager only through a SIP trunk. 

C. A SIP gateway requires a call agent for PSTN calls to be placed and received. An H.323 gateway does not require a call agent for PSTN calls to be placed and received. 

D. An H.323 gateway can register with Cisco Unified Communications Manager. A SIP gateway will show status of "Unknown". 

E. The H.323 gateway must be configured in Cisco Unified Communications Manager using a valid IP address on the gateway. The SIP gateway must be configured in Cisco Unified Communications Manager using the domain name. 

View Answer

Q8. Refer to the exhibit. 

HQ_MRGL is assigned to the HQ IP phones. BR_MRGL is assigned to the BR IP phones. The remote site BR IP phones support only the G.711 codec. Where should the transcoder reside? 

A. The transcoder should reside at the HQ site and assigned to HQ_MRG. 

B. The transcoder should reside at the BR site and assigned to BR_MRG. 

C. The transcoder should be assigned to its own MRG, which should then be assigned to the default device pool. 

D. A transcoder is not needed. The HQ phones will automatically change over to the G.711 codec. 

View Answer

Q9. In which two locations can you verify that a phone has a standby Cisco Unified Communications Manager? (Choose two.) 

A. RTMT 

B. phone menu 

C. Cisco Unified Serviceability 

D. phone webpage 

View Answer

Q10. Which two entities could be represented by device mobility groups? (Choose two.) 

A. countries 

B. regions 

C. directory numbers 

D. transcoders 

View Answer