Your success in Cisco ccnp route 300 101 dumps is our sole target and we develop all our ccnp 300 101 braindumps in a way that facilitates the attainment of this target. Not only is our ccnp routing and switching route 300 101 official cert guide study material the best you can find, it is also the most detailed and the most updated. examcollection 300 101 Practice Exams for Cisco CCDP 300 101 pdf are written to the highest standards of technical accuracy.
2026 New 300-101 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-101/
P.S. High value 300-101 answers are available on Google Drive, GET MORE: https://drive.google.com/open?id=1g3xBE0KhVLL-l1SXbBZMbJhQ4SK2THNQ
New Cisco 300-101 Exam Dumps Collection (Question 10 - Question 19)
Question No: 10
A network engineer is troubleshooting connectivity issues with a directly connected RIPng neighbor. Which command should directly connected RIPng neighbor adjacencies only?
A. router#show ipv6 rip next-hops
B. router#show ip rip neighbors
C. router#show ipv6 routers
D. router#show ipv6 rip database
Answer: A
Question No: 11
Which access list entry checks for an ACK within a packet header?
A. access-list 49 permit ip any any eq 21 tcp-ack
B. access-list 49 permit tcp any any eq 21 tcp-ack
C. access-list 149 permit tcp any any eq 21 established
D. access-list 49 permit tcp any any eq 21 established
Answer: C
Question No: 12
What is the purpose of configuring the router as a PPPoE client?
A. to provide VPN access over L2TP
B. to enable PPP session from the router to the termination device at the headend for metroEthernet connectivity
C. for DSL connectivity and removing the need for the end-user PC to run the PPPoE client software
D. for connecting the router to a cable modem, which bridges the Ethernet frames from the router to the cable modem termination system
Answer: C
Explanation:
DSL Technology used PPPoE protocol (service provide end) and user end required to be used same Protcol running as client to communicate with it
Question No: 13
An engineer is configuring a GRE tunnel interface in the default mode. The engineer has assigned an IPv4 address on the tunnel and sourced the tunnel from an Ethernet interface. Which option also is required on the tunnel interface before it is operational?
A. tunnel destination address
B. keepalives
C. IPv6 address
D. tunnel protection
Answer: A
Question No: 14
Which technology was originally developed for routers to handle fragmentation in the path between end points?
A. PMTUD
B. MSS
C. windowing
D. TCP
E. global synchronization
Answer: A
Question No: 15
Which configuration can you apply to a device so that it always blocks outbound web traffic on Saturdays and Sundays between the hours of 1:00 AM and 11:59 PM?
A. Option A
B. Option B
C. Option C
D. Option D
Answer: C
Question No: 16
Which two routing protocols are supported by Easy Virtual Network? (Choose two.)
A. RIPv2
B. OSPFv2
C. BGP
D. EIGRP
E. IS-IS
Answer: B,D
Question No: 17
Which two commands would be used to troubleshoot high memory usage for a process? (Choose two.)
A. router#show memory allocating-process table
B. router#show memory summary
C. router#show memory dead
D. router#show memory events
E. router#show memory processor statistics
Answer: A,B
Question No: 18
Which IPV6 address type does RIPng use for next-hop addresses?
A. anycast
B. global
C. multicast
D. site-local
E. link-local
Answer: E
Question No: 19
Refer to the exhibit.
Which command would verify if PBR reacts to packets sourced from 172.16.0.0/16?
A. show ip route
B. show policy-map
C. show access-lists
D. show route-map
Answer: D
Explanation:
The u201cshow route-map u201croute-map nameu201d displays the policy routing match counts so we can learn if PBR reacts to packets sourced from 172.16.0.0/16 or not.
100% Renewal Cisco 300-101 Questions & Answers shared by Thedumpscentre, Get HERE: http://www.thedumpscentre.com/300-101-dumps/ (New 436 Q&As)