Master the 300-370 Troubleshooting Cisco Wireless Enterprise Network content and be ready for exam day success quickly with this Testking 300-370 test questions. We guarantee it!We make it a reality and give you real 300-370 questions in our Cisco 300-370 braindumps.Latest 100% VALID Cisco 300-370 Exam Questions Dumps at below page. You can use our Cisco 300-370 braindumps and pass your exam.


2026 New 300-370 Exam Dumps with PDF and VCE Free: https://www.surepassexam.com/300-370-exam-dumps.html

Q1. An engineer is troubleshooting AP join issues on a wireless infrastructure. While gathering debugs, the engineer notices that one of the commands may generate an excessive an excessive amount of data on the console. Which command causes this to occur? 

A. debug capwap detail enable 

B. debug capwap errors enable 

C. debug capwap info enable 

D. debug capwap events enable 

E. debug capwap packet enable 

F. debug capwap payload enable 

Answer: B 

Q2. An engineer is troubleshooting non-802 11 interference and observes this output. Which type of interference signatures can the engineer identify? 

Refer to the exhibit. 

A. microwave 

B. DECT phone 

C. Bluetooth 

D. jammer 

Answer: A 

Q3. In a cisco OfficeExtend environment, which encryption type n und between the access point and the mass LAW controller? 

A. DTLS 

B. TIS 

C. STIS 

D. OpenSSL 

Answer: A 

Q4. An engineer is troubleshooting access point placement issues and suspects that poor placement is causing connectivity issues When running the show client detail <mac> command, the engineer notices this output Which option indicates poor access point placement? 

Refer to the exhibit. 

A. excessive number of bytes sent compared to bytes received 

B. high signal-to-noise ratio 

C. excessive number of data retries 

D. low ratio signal strength indicator 

E. duplicate received packets 

F. poor statistics for the last 90 seconds 

Answer: C,D 

Q5. A wireless engineer is unable to join lightweight access points to the Cisco Wireless Controller. The access points receive ip addresses from a DHCP pool configured on the core switch. Which action must be taken to resolve the issue? 

A. Upgrade the Wireless Controller to a newer IOS release. 

B. Configure option 43 on the DHCP pool. 

C. Configure option 82 on the Wireless controller. 

D. Change the management ip address on the Wireless Controller. 

Answer: C 

Q6. Some users are experiencing inconsistent performance on their mobile devices as they move throughout the building when browsing the Internet. Which feature provides a more consistent user experiences? 

A. low RSSI check 

B. 802.11r 

C. RX-SOP 

D. optimized roaming 

Answer: A 

Q7. Which three steps would a network engineer use to troubleshoot an AP join problem? (Choose three.) 

A. Validate the STP configuration. 

B. Verify the ping AP from the controller. 

C. Verify the ping AP from the client. 

D. Verify that the AP is getting an address from the DHCP server. 

E. I Validate the SNMP configuration. 

F. Verify the authentication configuration parameters. 

Answer: A,B,F 

Q8. A mobile workstation in a factory contains an AP that is configured as a workgroup bridge. When the workstation moves, it loses connectivity and disrupts operation. What can the engineer implement to minimize roaming problems? 

A. Use 802.1X authentication. 

B. Use Cisco Centralized Key Management for fast roaming. 

C. Use AES for encryption. 

D. Use the mobile station command. 

Answer: B 

Q9. An engineer is troubleshooting non-802 11 interference and observes this output. Which type of interference signatures can be identified? 

Refer to the exhibit. 

A. one frequency hopping Bluetooth 

B. two healthy CCK and one malformed OFDM 

C. three broadband jammers 

D. two strong microwave ovens and one moderate 

Answer: B 

Q10. A Wireless LAN Cisco engineer is troubleshooting 802. 11ac WLAN at customer site Doe to interferences with neighboring 802 11n networks the engineer must determine the current primary secondary channel allocation to enhance the current configuration. Channel 60 has been chosen by the customer as primary 20 MHz channel. Which combination determines the resulting primary 40 MHz and primary 80 MHZ channels? 

A. primary 40 MHz channel 62, primary 80 MM: channel 58 

B. primary 40 MHz channel 54, primary 80 MHz channel 58 

C. primary 40 MHz channel 64, primary 80 MHz channel 60 

D. primary 40 MHz channel 60, primary 80 MHz channel 56 

Answer: A