Testking offers free demo for 300-370 exam. "Troubleshooting Cisco Wireless Enterprise Network", also known as 300-370 exam, is a Cisco Certification. This set of posts, Passing the Cisco 300-370 exam, will help you answer those questions. The 300-370 Questions & Answers covers all the knowledge points of the real exam. 100% real Cisco 300-370 exams and revised by experts!


2026 New 300-370 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-370/

Q1. The AP is unable to join the controller. What is the cause of this error? Refer to the exhibit. 

A. The controller code version is lower than the code of the AP attempting to join. 

B. AP code is not the same as the controller and must download firmware. 

C. AP model % not compatible with the controller code version. 

D. The AP is riot conjured in the controller auth-list of acceptable APs. 

Answer: C 

Q2. A network engineer is troubleshooting why EAP authentication with a client is failing. Which two commands should be used to resolve the issue? (Choose two) 

A. debug dot1x notifications enable 

B. debug dot1x events enable 

C. debug arp 

D. debug aaa detail enable 

E. debug aaa events detail enable 

Answer: B,E 

Q3. Which three steps would a network engineer use to troubleshoot an AP join problem? (Choose three.) 

A. Validate the STP configuration. 

B. Verify the ping AP from the controller. 

C. Verify the ping AP from the client. 

D. Verify that the AP is getting an address from the DHCP server. 

E. I Validate the SNMP configuration. 

F. Verify the authentication configuration parameters. 

Answer: A,B,F 

Q4. A wireless engineer has completed the configuration of a new WLAN on the existing Cisco wireless infrastructure. During testing he found that the wireless client's authenticate and received the correct ip address from the switch, but they were not able to access any of the internal or external resources. Which action will resolve the issue? 

A. Configure static ip addresses for the wireless clients. 

B. Configure the default-router on the switch DHCP pool. 

C. Configure option 82 on the switch DHCP pool. 

D. Configure a dns-server on the switch DHCP pool. 

Answer: C 

Q5. You have successfully configured HA and SSO using two Cisco 5508 Wireless LAN Controllers. You are able to access the Active Primary WLC but are unable to access the Secondary Standby WLC. Which two methods will allow you to access the standby unit? (Choose two.) 

A. Via SSH to the Redundancy Management Interface. 

B. Via Service Port Interface. 

C. Via SSH to the Management Interface. 

D. Via console connection. 

Answer: C,D 

Q6. A company consists of two adjacent buildings, each with its own Cisco 5508 Wireless Controller with APs joined to the controller in the building. The two controllers are configured identically except for interface IP addresses. Only one SSID is being used in both buildings. The clients in building A are not experiencing any connectivity issues, but (he clients in building B report poor connections An engineer performs a site survey and finds co-channel interference, yet discovers mac Transmit Power Control was never performed on the APs and that Radio Resource Management is not functioning like it does in building A Furthermore, the controllers are in the same RF group and controller A is elected RF leader Which action will improve client connections in building B? 

A. Ensure WMM is enabled on the SSID. 

B. Manually select controller B as RF group leader. 

C. Configure controller B to be in a separate RF group. 

D. Doable the low data rates on the a radio and the b/g radio in building B. 

Answer: C 

Q7. A WLC receives a coverage hole detection alert from an AP. What two conditions must occur for the controller to dynamically mitigate the situation? (Choose two.) 

A. The AP serving the troubled client must currently have a power level 2 or lower. 

B. The client must be able to dynamically raise its power level to match the new AP power. 

C. The AP must be RF visible to additional APs on the other side of the coverage hole for calibration. 

D. The client must have WMM-PS disabled to allow for the increased power usage. 

E. The AP serving the troubled client must currently have a power level higher than 2. 

Answer: A,B 

Q8. A WLAN engineer has just completed a wireless network installation using Cisco 2700 

series access points. After checking the WLC, it seems that the APs are running in medium power. What effect will this have in the APs? 

A. Due to insufficient power, the access points are not broadcasting any Wireless networks. 

B. Due to insufficient power, only the 2 4 GHz radio is up. 

C. Due to insufficient power the access points have dynamically shifted from 3x4 to 3x3. 

D. Due to insufficient power the access points have dynamically shifted from 4x4 to 3x3. 

Answer: C 

Q9. Clients are failing EAP authentication A debug shows that an EAP handshake started and the clients are then de-authenticated. Which two issues can cause this problem'? (Choose two.) 

A. The clients are configured for machine authentication, but the RADIUS server is configured for user authentication. 

B. The WLC has not been added to the RADIUS server as a client. 

C. The WLC certificate has changed. 

D. The shared secret of the WLC and RADIUS server do not match. 

E. The WLAN is not configured for the correct EAP supplicant type. 

Answer: B,E 

Q10. Which two statements about the WLAN are true? (Choose two) 

Refer to the exhibit. 

A. The client has a 5 GHz connection. 

B. The client has authenticated. 

C. The client is 802.11n capable. 

D. The Cisco device is a 3600 series AP. 

E. 802 11b data rates are disabled in this WLAN 

Answer: C,E