All About Pinpoint 300-370 vce

Q1. An engineer is troubleshooting AP join issues on a wireless infrastructure. While gathering debugs, the engineer notices that one of the commands may generate an excessive an excessive amount of data on the console. Which command causes this to occur? 

A. debug capwap detail enable 

B. debug capwap errors enable 

C. debug capwap info enable 

D. debug capwap events enable 

E. debug capwap packet enable 

F. debug capwap payload enable 

View Answer

Q2. RAG DROP 

Drag and drop the IP address range on the left onto the specific purpose for multicast groups on the right. Not all options are used. 

View Answer

Q3. When implementing interface groups, how are the IP addresses sourced via DHCP for wireless clients? 

A. through the primary interface of the group 

B. through round robin between interfaces 

C. through interface group definition 

D. through the interface receiving the first response 

View Answer

Q4. Which statement about the join process of the access point is true? Refer to the exhibit. 

A. The time on the controller is outside of the certificates validity time interval, so the join phase failed. 

B. The AP successfully joined the controller. 

C. The AP moved from this controller to its primary controller. 

D. The AP failed to join because the MAC address of the AP was not correct on the controller. 

E. The controller rejected all discovery requests from the AP because they were not received on the management interface subnet. 

View Answer

Q5. Two 5508 Wireless Lan Controllers are managing all Access Points throughout the network The WLCs are located in different locations to provide geographical redundancy A Mobility Group has been configured on both WLCs and has a UP status on both Controllers The APs m location A are statically configured to use Controller A as the Primary and Controller B as the Secondary If the WLC in location A goes offline, the APs successfully join the WLC m location B but they do not failover to their Primary configured Controller What configuration task will fix this issue' 

A. Change the AP Failover Priority to critical. 

B. Enable AP Fallback globally on the WLC. 

C. Configure the WLC in location A as Primary using the CAPWAP AP Controller IP Address command on all the location A Access Points. 

D. Use DHCP Option 43 and specify WLC in location A as Primary. 

View Answer

Q6. Which statement describes how the Hand Select feature works on the wireless controller? Refer to the exhibit. 

A. The access point uses the load balancing feature to move the clients to 5 Ghz. 

B. The access point changes the DTIM period on the 2 4 Ghz band. 

C. The access point recommends the band in the association response to the client. 

D. The access point ignores and delays the probe request of the client on the 2 4 Ghz. 

View Answer

Q7. A WLAN engineer has just completed a wireless network installation using Cisco 2700 

series access points. After checking the WLC, it seems that the APs are running in medium power. What effect will this have in the APs? 

A. Due to insufficient power, the access points are not broadcasting any Wireless networks. 

B. Due to insufficient power, only the 2 4 GHz radio is up. 

C. Due to insufficient power the access points have dynamically shifted from 3x4 to 3x3. 

D. Due to insufficient power the access points have dynamically shifted from 4x4 to 3x3. 

View Answer

Q8. A user reports being unable to connect to a server with a certain program while connected to wireless. Wh.ch troubleshooting methodology can be used to begin the troubleshooting process? 

A. top-down 

B. shoot from the hip 

C. follow the path 

D. bottom-up 

E. divide and conquer 

View Answer

Q9. A company consists of two adjacent buildings, each with its own Cisco 5508 Wireless Controller with APs joined to the controller in the building. The two controllers are configured identically except for interface IP addresses. Only one SSID is being used in both buildings. The clients in building A are not experiencing any connectivity issues, but (he clients in building B report poor connections An engineer performs a site survey and finds co-channel interference, yet discovers mac Transmit Power Control was never performed on the APs and that Radio Resource Management is not functioning like it does in building A Furthermore, the controllers are in the same RF group and controller A is elected RF leader Which action will improve client connections in building B? 

A. Ensure WMM is enabled on the SSID. 

B. Manually select controller B as RF group leader. 

C. Configure controller B to be in a separate RF group. 

D. Doable the low data rates on the a radio and the b/g radio in building B. 

View Answer

Q10. A Wireless LAN Cisco engineer is troubleshooting 802. 11ac WLAN at customer site Doe to interferences with neighboring 802 11n networks the engineer must determine the current primary secondary channel allocation to enhance the current configuration. Channel 60 has been chosen by the customer as primary 20 MHz channel. Which combination determines the resulting primary 40 MHz and primary 80 MHZ channels? 

A. primary 40 MHz channel 62, primary 80 MM: channel 58 

B. primary 40 MHz channel 54, primary 80 MHz channel 58 

C. primary 40 MHz channel 64, primary 80 MHz channel 60 

D. primary 40 MHz channel 60, primary 80 MHz channel 56 

View Answer