Act now and download your Cisco 300-370 test today! Do not waste time for the worthless Cisco 300-370 tutorials. Download Rebirth Cisco Troubleshooting Cisco Wireless Enterprise Network exam with real questions and answers and begin to learn Cisco 300-370 with a classic professional.
2026 New 300-370 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-370/
Q1. Which Cisco WLC debug command allows you to determine if the certificate process is failing in the CAPWAP messages?
A. debug pm pki enable
B. debug cert events enable
C. debug capwap events enable
D. debug capwap packet enable
E. debug capwap errors enable
Answer: E
Q2. A WLC receives a coverage hole detection alert from an AP. What two conditions must occur for the controller to dynamically mitigate the situation? (Choose two.)
A. The AP serving the troubled client must currently have a power level 2 or lower.
B. The client must be able to dynamically raise its power level to match the new AP power.
C. The AP must be RF visible to additional APs on the other side of the coverage hole for calibration.
D. The client must have WMM-PS disabled to allow for the increased power usage.
E. The AP serving the troubled client must currently have a power level higher than 2.
Answer: A,B
Q3. An engineer is using various techniques to discover and isolate rogues on the network. For which technique must the engineer consider legal ramifications?
A. rogue AP containment
B. RF detection
C. switch port tracing
D. wire detection
E. Cisco Prime Infrastructure location services
Answer: A
Q4. An engineer is creating a custom rogue classification rule directly on a controller. Which two conditions are possible when adding a custom rule to a controller? (Choose two.)
A. internal
B. ad hoc
C. client-count
D. duration
E. WLAN
F. open authentication
Answer: A,D
Q5. An engineer is troubleshooting non-802.11 interference and observes the shown output. Which interference signature is the most harmful to Wi-Fi?
Refer to the exhibit.
A. cordless phone
B. microwave oven
C. 2 4 GHz wideband jammer
D. FHSS Bluetooth
E. analog video camera
Answer: A
Q6. An engineer is concerned about rogue-on-wire and wants to enable port security. Which guideline must the engineer follow?
A. Configure Switched Port Analyzer destination ports as secure.
B. Use 802 1x with port security to prevent MAC spoofing.
C. Enable port security on dynamic access ports.
D. Employ static MAC address configuration for APs with port security.
Answer: A
Q7. An engineer is deploying a wireless infrastructure and must use Layer 2 discovery for access point association. Which configuration meets this requirement?
A. Configure the Access Points and WLC management interface on the same VLAN.
B. Configure a DNS A RECORD to point to the controller.
C. Configure option 43 on The APs DHCP scope.
D. Configure the AP using a serial connection to indicate its controller.
Answer: A
Q8. A wireless engineer is unable to join lightweight access points to the Cisco Wireless Controller. The access points receive ip addresses from a DHCP pool configured on the core switch. Which action must be taken to resolve the issue?
A. Upgrade the Wireless Controller to a newer IOS release.
B. Configure option 43 on the DHCP pool.
C. Configure option 82 on the Wireless controller.
D. Change the management ip address on the Wireless Controller.
Answer: C
Q9. When implementing interface groups, how are the IP addresses sourced via DHCP for wireless clients?
A. through the primary interface of the group
B. through round robin between interfaces
C. through interface group definition
D. through the interface receiving the first response
Answer: B
Q10. An engineer is troubleshooting non-802 11 interference and observes this output. Which type of interference signatures can be identified?
Refer to the exhibit.
A. one frequency hopping Bluetooth
B. two healthy CCK and one malformed OFDM
C. three broadband jammers
D. two strong microwave ovens and one moderate
Answer: B