High quality of 300-370 exam answers materials and braindumps for Cisco certification for IT examinee, Real Success Guaranteed with Updated 300-370 pdf dumps vce Materials. 100% PASS Troubleshooting Cisco Wireless Enterprise Network exam Today!
2026 New 300-370 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-370/
Q1. A user reports being unable to connect to a server with a certain program while connected to wireless. Wh.ch troubleshooting methodology can be used to begin the troubleshooting process?
A. top-down
B. shoot from the hip
C. follow the path
D. bottom-up
E. divide and conquer
Answer: A
Q2. A WLAN was installed at a high AP density. DTPC is lowering the transmit power of many APs too low. Which change m the DTPC transmit power threshold must be made to allow APs to globally increase AP transmit power by 3dBm?
A. from 70 dBm to 73 dBm
B. from -70 dBm to -73 dBm
C. from 70 dBm to 67 dBm
D. from -70 dBm to -67 dBm
Answer: D
Q3. Which two statements about the WLAN are true? (Choose two)
Refer to the exhibit.
A. The client has a 5 GHz connection.
B. The client has authenticated.
C. The client is 802.11n capable.
D. The Cisco device is a 3600 series AP.
E. 802 11b data rates are disabled in this WLAN
Answer: C,E
Q4. A WLC receives a coverage hole detection alert from an AP. What two conditions must occur for the controller to dynamically mitigate the situation? (Choose two.)
A. The AP serving the troubled client must currently have a power level 2 or lower.
B. The client must be able to dynamically raise its power level to match the new AP power.
C. The AP must be RF visible to additional APs on the other side of the coverage hole for calibration.
D. The client must have WMM-PS disabled to allow for the increased power usage.
E. The AP serving the troubled client must currently have a power level higher than 2.
Answer: A,B
Q5. While reviewing CleanAir data in Cisco Prime Infrastructure, an engineer notices that a wideband jammer is not sending its Interferer Security Trap correctly. The engineer determines that the default seventy level has been changed. Which value does the engineer select to reset the seventy level to its factory setting?
A. informational
B. major
C. minor
D. warning
E. critical
Answer: D
Q6. A WLAN engineer has just completed a wireless network installation using Cisco 2700
series access points. After checking the WLC, it seems that the APs are running in medium power. What effect will this have in the APs?
A. Due to insufficient power, the access points are not broadcasting any Wireless networks.
B. Due to insufficient power, only the 2 4 GHz radio is up.
C. Due to insufficient power the access points have dynamically shifted from 3x4 to 3x3.
D. Due to insufficient power the access points have dynamically shifted from 4x4 to 3x3.
Answer: C
Q7. An engineer must open a support case with Cisco TAC. Which two commands verify the model and serial number of a controller? (Choose two)
A. show sysinfo
B. show udi
C. show inventory
D. show boot
E. show tech-support
Answer: A,B
Q8. An engineer has configured 802 1x for the network and all but one of the APs are passing authentication. Which configuration is causing the failure?
A. The AP has override global credentials checked.
B. The switch AAA credentials do not match what is configured on ISE.
C. The controller 802 1x supplicant credentials do not match what is configured on ISE
D. EAP-FAST is configured on ISE for this AP.
Answer: A
Q9. Which statement about the usage of the debug command in a Cisco Unified Wireless Network is true?
A. Debug is enabled until manual shut off.
B. Debug is a message logging severity 7.
C. Debug is a restricted command and is not available in the AP CLI.
D. Debug is available on the WLC serial console and web interface.
Answer: B
Q10. Employees upgraded company issued OS devices. Which are configured to authenticate to the network using WPA2-Eniefpnse 802 lx with LEAP As a result, the devices are no longer able to authenticate Which action must the engineer do 10 resolve the issue?
Refer to the exhibit.
A. Redeploy the existing configuration profile.
B. Change LEAP certificate on the ACS server.
C. Reset the network settings on the devices.
D. Rejoin the enterprise network manually.
E. Deploy a new configuration profile with LEAP enabled
Answer: B