What Printable 352-001 dumps Is?

Q1. In an OSPF network, users in a particular OSPF non-backbone area are complaining about slow access speeds to a shared corporate resource in another OSPF area. Traceroutes show that theusers are taking a suboptimal default route to the destinations. Which solution will improve access speed? 

A. Make the area totally stubby so that the default can be followed along the best path. 

B. Create a virtual link between the areas so that traffic can shortcut directly between them. 

C. Implement policy routing to channel the traffic in the optimal direction. 

D. Leak specific summaries on the ABRs for the remote subnets in addition to the default. 

View Answer

Q2. Which mechanism provides a Layer 2 fault isolation between data centers? 

A. TRILL 

B. LISP 

C. advanced VPLS 

D. OTV 

E. fabric path 

View Answer

Q3. A network designer is working with a company to improve convergence at the Layer 2 control plane and decides to use LACP. Which of these components does LACP use to create the system ID? 

A. LACP system priority and switch MAC address 

B. LACP port priority and switch MAC address 

C. LACP port priority and port number 

D. LACP system priority and port number 

View Answer

Q4. Your company will attach to a new Gigabit Ethernet-based wide area network from the local service provider for remote connectivity. Each connection will have a 150 Mb/s committed information rate. For the design of this new service, which QoS mechanism should be used to ensure low packet loss toward the service provider network? 

A. shaping 

B. policing 

C. CBWFQ 

D. RED 

View Answer

Q5. You are designing a network for a branch office. In order to improve convergence time, you are required to use the BFD feature. Which four routing protocols can you use to facilitate this? (Choose four.) 

A. EIGRP 

B. IS-IS 

C. BGP 

D. static 

E. RIP 

View Answer

Q6. Refer to the exhibit. 

Company A is running a single-area OSPF, and Company B is running RIP as the IGP with no overlapping IP address spaces. Company A has just acquired Company B and both networks must be merged. Which three design components are recommended to guarantee connectivity and redundancy between the two networks? (Choose three.) 

A. Enable mutual redistribution between OSPF and RIP on one border router. 

B. Enable mutual redistribution between OSPF and RIP on Router A and Router B using route tags. 

C. Increase the administrative distance to 130 for the OSPF external prefixes on Router A and Router B. 

D. Implement an ACL on Router A and Router B to prevent OSPF external routes from being installed in the OSPF database. 

E. Filter external routes on Router A and Router B based on route tags. 

View Answer

Q7. In a network design using carrier Ethernet, which three mechanisms can be used to improve Layer 2 down detection and thereby reduce routing convergence time? (Choose three.) 

A. BFD 

B. Ethernet port debounce timers 

C. link-state tracking 

D. object tracking 

E. fast IGP hello 

View Answer

Q8. There is an MPLS-enabled link constantly flapping on an MPLS VPN network. Given that the network runs OSPF as the IGP protocol, which design mechanism will stabilize the network and avoid constant reconvergences? 

A. BFD 

B. IP Event Dampening 

C. OSPF fast hellos 

D. partial SPF 

View Answer

Q9. A network designer wants to improve a company network design due to multiple network crashes. Which technology would allow for the restore of a network connection without informing the Layer 3 protocol? 

A. Bidirectional Forwarding Detection 

B. automatic protection switching 

C. UniDirectional Link Detection 

D. Ethernet OAM 

View Answer

Q10. You have been asked to establish a design that will allow your company to migrate from a WAN service to a Layer 3 VPN service. In your design, you are keeping some WAN links between critical sites as a backup for this service. You plan to use OSPF as your IGP and BGP for the PE-CE protocol. When the Layer 3 VPN service is available, how will you prevent transit traffic over the backup links? 

A. Redistribute routes at the CE as external type 1. 

B. Redistribute routes at the CE as external type 2. 

C. Use conditional advertisement only when the Layer 3 service is down. 

D. Manually turn off the backdoor link when the Layer 3 service is up. 

View Answer