Microsoft 70-743 Exam Questions and Answers 2021

NEW QUESTION 1
You have a server named Server1 that runs Windows Server 2021. Server1 has the DHCP Server and the Windows Deployment Service server roles installed.
Server1 is located on the same subnet as client computers.
You need to ensure that clients can perform a PXE boot from Server1.
Which two IPv4 options should you configure in DHCP? Each correct answer presents part of the solution.

• A. 003 Router
• B. 066 Boot Server Host Name
• C. 015 DNS Domain Name
• D. 006 DNS Servers
• E. 060 Option 60

Answer: AB

NEW QUESTION 2
HOTSPOT
You deploy a new Hyper-V host named Server1 that runs Windows Server 2021. You implement receive side scaling (RSS) on Server1.
The chipset on Server1 does not support NetDM A.
All of the equipment on your network supports 10-Gbps connectivity. On Server1, you deploy a virtual machine named VM1.
You configure VM1 to aggregate all of the Windows and non-Windows tog files for all of the servers on the network.
VM1 has four virtual processors. You discover that VM1 drops packets.
Which two options should you run? To answer, select the appropriate options in the answer area.

Answer:

Explanation:

NEW QUESTION 3
Your network contains an Active directory forest named contoso.com. The forest has a Distributed File System (DFS) namespace named \contoso.comnamespace1.
The domain contains a file server named Server1 that runs Windows Server 2021. You create a folder named Folder1 on Server1.
Which two cmdlets should you use? Each correct answer presents part of the solution. NOTE: Each correct selection is worth one point.

• A. New-DfsnFolderTarget
• B. Install-WindowsFeature
• C. Grant-DfsnAccess
• D. New-DfsnFolder
• E. New-SmbShare

Answer: BC

NEW QUESTION 4
You have 2000 devices, One hundred of the devices are mobile devices that have physical addresses beginning with 98-5F.
You have a DHCP server named Server1.
You need to ensure that the mobile devices register their host name by using a DNS suffix of mobile.contoso.com

• A. From the properties of Scopte1, Modify the Conflict detection attempts setting.
• B. From the properties of Scope1, Configure Name Protection.
• C. From the Properties of IPV4, configure the bindings.
• D. From IPV4, create a new filter.
• E. From the properties of Scope1, create an exclusion range.
• F. From IPv4, run the DHCP Policy Configuration Wizard.
• G. From Control Panel, modify the properties of Ethernet.
• H. From Scope1, create a reservation

Answer: F

NEW QUESTION 5
HOT SPOT
You have a Hyper-V host named Server1 that runs Windows Server 2021. Server1 has two network adaptors named NK1 and NIC2. Server2 has two virtual switches named vSwitch1 and vSwitch2. N1C1 connects to vSwitch1. NIC2 connects to vSwitch2
Server1 hosts a virtual machine named VM1. VM1 has two network adapters named vmNIC1 and vmNIC1. VmNIC1 connects to vSwitch1. VmNIC2 connects to vSwitch2.
You need to create a NIC team on VM1.
What should you run on VM1? To answer, select the appropriate options in the answer area. NOTE: Each correct selection is worth one point.

Answer:

Explanation: Name NICTEAM1 TeamMembers vmNIC1, vmNIC2 –TeamingMode $var1 –LoadBalancingAlgorithm
$var2

NEW QUESTION 6
HOTSPOT
You have a server named Server1 that runs Windows Server 2021. Server1 has the Web Application Proxy role service installed.
You are publishing an application named App1 that will use Integrated Windows authentication as shown in the following graphic.

Use the drop-down menus to select the answer choice that completes each statement based on the information presented in the graphic.

Answer:

Explanation: Publish an Integrated Windows authenticated-based Application for WebBrowser Clients Step 1: (configure the Backend server SPN – see first bulleted item below)
Before you begin, make sure that you have done the following: Step 2: http//server2.contoso.com/publish/app1
Use the same URL as the backend server URL.
Web Application Proxy can translate host names in URLs, but cannot translate path names. Therefore, you can enter different host names, but you must enter the same path name. For example, you can enter an external URL of https://apps.contoso.com/app1/ and a backend server URL of http://app-server/app1/. However, you cannot enter an external URL of https://apps.contoso.com/app1/ and a backend server URL of https://apps.contoso.com/internalapp1/. References:
https://technet.microsoft.com/en-us/library/dn383640(v=ws.11).aspx

NEW QUESTION 7
HOTSPOT
Your network contains an Active Directory forest. The forest contains two sites named Site1 and Site2. Site1 contains 10 domain controllers. Site1 and Site2 connect to each other by using a WAN link.
You run the Active Directory Domain Services Configuration Wizard as shown in the following graphic.

Server3 is the only server in Site2.
Use the drop-down menus to select the answer choice that completes each statement based on the information presented in the graphic.

Answer:

Explanation: Box1: stop and start the Active Directory Domain Services (AD DS) Box 2: Can log on if they have previously logged on.
By selectively caching credentials, RODCs address some of the challenges that enterprises can encounter in branch offices and perimeter networks (also known as DMZs) that may lack the physical security that is commonly found in datacenters and hub sites.

NEW QUESTION 8
HOTSPOT
Your network contains an Active Directory domain named contoso.com. The domain contains four servers named Server1, Server2, Server3, and Server4 that run Windows Server 2021.
Server1 and Server2 are nodes in a Hyper-V cluster named Cluster1. You have a highly available virtual machine named VM1. Server1 is the owner node of VM1. Server3 and Server4 are nodes of a scale-out file server named Cluster2.
The storage on Server1 is configured as shown in the following table.

VM1 is stored in C:ClusterStorageVolume1.
You need to move the virtual disk of VM1 to a different location.
What should you do? To answer, select the appropriate options in the answer area.

Answer:

Explanation: Box 1: Failover Cluster Manager
You can use Failover Cluster Manager to do a Storage Migration to a shared folder. Box 2: \Cluster2Share1
For a highly-available VM, the storage must be accessible by all nodes in the cluster. Therefore, in this scenario, we have to use the file share.
You c References:
https://blogs.msdn.microsoft.com/clustering/2012/04/26/windows-server-2012-storage-migrationfor- cluster-managed-virtual-machines/

NEW QUESTION 9
HOTSPOT
You have a Windows Server 2021 failover cluster that has a cluster network named ClusterNetwork1. You need to ensure that ClusterNetwork1 is enabled for cluster communication only.
What command should you run? To answer, select the appropriate options in the answer area.

Answer:

Explanation: Box 1: Get-ClusterNetwork
Cluster network roles can be changed using PowerShell command, Get-ClusterNetwork. For example:
(Get-ClusterNetwork “Cluster Network 1”). Role =1
Box 2: Role
Cluster Network Roles:
Cluster networks are automatically created for all logical subnets connected to all nodes in the Cluster. Each network adapter card connected to a common subnet will be listed in Failover Cluster Manager. Cluster networks can be configured for different uses.
Three roles: References:
https://blogs.technet.microsoft.com/askcore/2014/02/19/configuring-windows-failover-clusternetworks/

NEW QUESTION 10
You have an Active Directory domain that contains several Hyper-V hosts that run Windows Server 2021.
You plan to deploy network virtualization and to centrally manage Datacenter Firewall policies. Which component must you install for the planned deployment?

• A. the Routing role service
• B. the Canary Network Diagnostics feature
• C. the Network Controller server role
• D. the Data Center Bridging feature

Answer: C

Explanation: Using Windows PowerShell, the REST API, or a management application, you can use Network Controller to manage the following physical and virtual network infrastructure:
References:
https://technet.microsoft.com/en-us/library/dn859239.aspx

NEW QUESTION 11
Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution that might meet the stated goals. Some question sets might have more than one correct solution, while others might not have a correct solution.
After you answer a question in this sections, you will NOT be able to return to it. As a result, these questions will not appear in the review screen.
You have a Hyper-V host named Server1 that hosts a virtual machine named VM1. Server1 and VM1 run Windows Server 2021.
The settings for VM1 are configured as shown in the exhibit below.

You need to ensure that you can use the Copy-VMFile cmdlet on Server1 to copy files from VM1. Solution: You need to enable the Data Exchange integration service for VM1.
Does this meet the goal?

• A. YES
• B. NO

Answer: A

NEW QUESTION 12
You have a virtual machine named VM1 that runs Windows Server 2021, VM1 hosts a service that requires high network throughput.
VM1 has a virtual network adapter that connects to a Hyper-V switch named vSwitch1. vSwitch1 has one network adapter. The network adapter supports Remote Direct Memory Access (RDMA), the single root I/O virtualization (SR-IOV) interface, Quality of Service? (QoS), and Receive Side Scaling (RSS).
You need to ensure that the traffic from VM1 can be processed by multiple networking processors. Which Windows PowerShell command should you run on the host of VM1?

• A. Set-NetAdapterRss
• B. Set-NetAdapterRdma
• C. Set-NetAdapterQos
• D. Set-NetAdapterSriov

Answer: D

NEW QUESTION 13
Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution. Determine whether the solution meets the stated goals.
Your network contains an Active Directory domain named contoso.com. The domain contains a DNS server named Server1. All client computers run Windows 10.
On Server1, you have the following zone configuration.

You need to ensure that all of the client computers in the domain perform DNSSEC validation for the fabrikam.com namespace.
Solution: From a Group Policy object (GPO) in the domain, you modify the Network List Manager Policies.
Does this meet the goal?

• A. Yes
• B. No

Answer: B

Explanation: Network List Manager Policies are security settings that you can use to configure different aspects of
how networks are listed and displayed on one computer or on many computers. Network List Manager Policies are not related to DNSSEC.
References:
https://technet.microsoft.com/en-us/library/jj966256(v=ws.11).aspx https://technet.microsoft.com/nl-nl/itpro/windows/keep-secure/network-list-managerpolicies? f=255&MSPPError=-2147217396
The right way would be by using network policies:
Add-DnsServerClientSubnet -Name “subnet4” -IPv4Subnet 172.16.1.0/24 -PassThru
Add-DnsServerQueryResolutionPolicy -Name “blockqueries” -Action IGNORE -ClientSubnet “EQ,subnet4” -PassThru
See also: https://technet.microsoft.com/en-us/windows-server-docs/networking/dns/deploy/apply- filters-on-dns-queries

NEW QUESTION 14
Your network contains three subnets, a production subnet that contains production servers, a development network that contains development servers, and a client network that contains client computers.
The development network is used to test applications and reproduces servers that are located on the production network. The development network and the production network use the same IP address range.
A developer has a client computer on the client network. The developer reports that when he attempts to connect to the IP address 10.10.1.6 from his computer, he connects to a server on the production network.
You need to ensure that when the developer connects to 10.10.1.6, he connects to a sever on the development network
Which cmdlet should you use?

• A. New-NetNeighbor
• B. New-NetRoute
• C. Set-NetTcpSetting
• D. Set-NetNeighbir

Answer: B

NEW QUESTION 15
HOTSPOT
Your network contains an Active Directory domain named contoso.com. The domain contains two servers named Server1 and Server2 that run Windows Server 2021.
Server1 has IP Address Management (IPAM) installed. Server2 has the DHCP Server role installed. The IPAM server retrieves data from Server2.
The domain has two users named User1 and User2 and a group named Group1. User1 is the only member of Group1.
Server1 has one IPAM access policy. You edit the access policy as shown in the Policy exhibit. (Click the Exhibit button.)

The DHCP scopes are configured as shown in the Scopes exhibit. (Click the Exhibit button.)

For each of the following statements, select Yes if the statement is true. Otherwise, select No.

Answer:

Explanation:

NEW QUESTION 16
Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution. Determine whether the solution meets the stated goals.
Your network contains an Active Directory domain named contoso.com. The domain contains a DNS server named Server1. All client computers run Windows 10.
On Server1, you have the following zone configuration.

You have the following subnets defined on Server1.

You need to prevent Server1 from resolving queries from DNS clients located on Subnet4. Server1 must resolve queries from all other DNS clients.
Solution: From the Security Setting of each zone on Server1, you modify the permissions. Does this meet the goal?

• A. Yes
• B. No

Answer: B

NEW QUESTION 17
DRAG DROP
You have a network that contains several servers that run Windows Server 2021.
You need to use Desired State Configuration (DSC) to configure the servers to meet the following requirements:
How should you configure the DSC recourses? To answer, drag the appropriate values to the correct locations. Each value may be used once, more than once, or not at all. You may need to drag the split bar between panes or scroll to view content.

Answer:

Explanation: Box 1: WindowsFeature
The WindowsFeature resource in Windows PowerShell Desired State Configuration (DSC) provides a mechanism to ensure that roles and features are added or removed on atarget node.
Box 2: Present
The Ensure Property indicates if the role or feature is added. To ensure that the role or feature is
added, set this property to "Present" To ensure that the role or feature is removed, set the property to "Absent".
Example:
WindowsFeature RoleExample
{
Ensure = "Present"
# Alternatively, to ensure the role is uninstalled, set Ensure to "Absent" Name = "Web-Server"# Use the Name property from Get-WindowsFeature
}
Box 3: Service
The Service resource in Windows PowerShell Desired State Configuration (DSC) provides a mechanism to manage services on the target node.
Box 4: Running
The State property indicates the state, either Running or Stopped, you want to ensure for the service. References:
https://msdn.microsoft.com/en-us/powershell/dsc/windowsfeatureresource https://msdn.microsoft.com/en-us/powershell/dsc/serviceresource

NEW QUESTION 18
You have a server named Server1 that runs Windows Server 2021. Server1 is an IP Address Management (IPAM) server that collects DHCP and DNS logs and events for your entire network. You need to get the IP addresses that were assigned to a client computer named Computer1 during the last week.
What should you do on Server1?

• A. Open Event Viewer and click Windows Log
• B. Filter the Forwarded Events log for Computer1.
• C. Open Event Viewer and click Windows Log
• D. Filter the Security log for Computer1.
• E. Run the Get-IpamDhcpConfigurationEvent cmdlet.
• F. Run the Get-IpamIpAddressAuditEvent cmdle

Answer: D

Explanation: References: https://docs.microsoft.com/en-us/powershell/module/ipamserver/getipamipaddressauditevent? view=win10-ps