All About Verified 300-115 braindumps

New Questions 3

Which command does a network engineer use to verify the spanning-tree status for VLAN 10?

A. switch# show spanning-tree vlan 10

B. switch# show spanning-tree bridge

C. switch# show spanning-tree brief

D. switch# show spanning-tree summary

E. switch# show spanning-tree vlan 10 brief

View Answer

New Questions 4

In which two ways can a port respond to a port-security violation? (Choose two.)

A. The port enters the en-disabled state

B. The Security Violation counter is incremented and the port sends an SNMP trap

C. The Security Violation counter is incremented and the port sends a critical syslog message to the console

D. The port triggers an EEM script to notify support staff and continues to forward traffic normally D

E. The port immediately begins to drop all traffic.

F. The port enters the shutdown state.

View Answer

New Questions 5

Refer to the exhibit.

The users in an engineering department that connect to the same access switch cannot access the network. The network engineer found that the engineering VLAN is missing

from the database. Which action resolves this problem?

A. Disable VTP pruning and disable 802.1q.

B. Update the VTP revision number.

C. Change VTP mode to server and enable 802.1q.

D. Enable VTP pruning and disable 802.1q.

View Answer

New Questions 6

Refer to the exhibit.

When a network administrator is attempting an SSH connection to the device, in which order does the device check the login credentials?

A. RADIUS server, local username, line password

B. RADIUS server, line password, local username

C. Line password, local username, RADIUS server

D. Line password, RADIUS server, local username

View Answer

New Questions 7

What happens if an interface within channel group is configure as SPAN destination?

A. portchannel will forward traffic to source span

B. will not be operational

C. the link will be in error-disable

View Answer

New Questions 8

Which statement about the UDLD protocol is true?

A. UDLD is a Cisco-proprietary Layer 2 protocol that enables devices to monitor the physical status of links and detect unidirectional failures.

B. UDLD is a Cisco-proprietary Layer 2 protocol that enables devices to advertise their identity, capabilities, and neighbors on a local area network.

C. UDLD is a standardized Layer 2 protocol that enables devices to monitor the physical status of links and detect unidirectional failures.

D. UDLD is a standardized Layer 2 protocol that enables devices to advertise their identity, capabilities, and neighbors on a local area network.

View Answer

New Questions 9

Which statement describes what happens when a switch enters dual active recovery mode?

A. The switch shuts down and waits for the VSL link to be restored before sending traffic.

B. All interfaces are shut down in the formerly active virtual switch member, but the new active virtual switch forwards traffic on all links.

C. The switch continues to forward traffic out all links and enables spanning tree on VSL link and all other links to prevent loops.

D. The VSS detects which system was last in active state and shuts down the other switch.

View Answer

New Questions 10

A physical switch port is part of an EtherChannel group. What happenes while the same port configured as a SPAN destination?

A. The port forwards traffic in the EtherChannel group and acts as a SPAN source simultaneously.

B. The port is removed from the EtherChannel group.

C. The port is put in the errdisabled state and can only be reenabled manually.

D. The operation is not allowed as an EtherChannel member cannot be a SPAN source port.

View Answer

New Questions 11

an EtherChannel configured and one of the port was used as SPAN destination. What will be the result?

A. the etherchannel will not be operational because the port cannot be used as SPAN destination

B. etherchannel will discard the port used

C. the etherchannel will shutdown

View Answer

New Questions 12

You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration.

You are adding new VLANs. VLAN500 and VLAN600 to the topology in such way that you need to configure SW1 as primary root for VLAN 500 and secondary for VLAN 600 and SW2 as primary root for VLAN 600 and secondary for VLAN 500. Which configuration step is valid?

A. Configure VLAN 500 & VLAN 600 on both SW1 & SW2

B. Configure VLAN 500 and VLAN 600 on SW1 only

C. Configure VLAN 500 and VLAN 600 on SW2 only

D. Configure VLAN 500 and VLAN 600 on SW1 ,SW2 and SW4

E. On SW2; configure vtp mode as off and configure VLAN 500 and VLAN 600; configure back to vtp server mode.

View Answer

New Questions 13

Refer to the exhibit.

Switch A, B, and C are trunked together and have been properly configured for VTP. Switch C receives VLAN information from the VTP server Switch A, but Switch B does not receive any VLAN information. What is the most probable cause of this behavior?

A. Switch B is configured in transparent mode.

B. Switch B is configured with an access port to Switch A, while Switch C is configured with a trunk port to Switch B.

C. The VTP revision number of the Switch B is higher than that of Switch A.

D. The trunk between Switch A and Switch B is misconfigured.

View Answer