how many questions of 300-365 vce?

Q1. A customer has implemented several WLANs in an auditorium utilizing a newly dedicated WLC and is experiencing excessive channel utilization regardless of occupancy. Which action reduces channel utilization without removing SSIDs? 

A. Disable MCS data rates 0 through 11. 

B. Disable MCS data rates used by 40 MHz channels. 

C. Disable data rates that use CCK. 

D. Disable VHT data rates. 

View Answer

Q2. A client reports that video is not streaming. The administrator determines the client is connecting at a data rate of 12 Mbps and is trying to stream to a valid multicast address on the network. What three items should the administrator check next to troubleshoot the issue? (Choose three) 

A. IGMP snooping is turned off because the client cannot request to join a group, only access points can. 

B. Video-stream for the multicast video is configured in the controller. 

C. WLAN has been set for a QoS value of Platinum. 

D. WLAN has been configured to allow multicast-direct to work correctly and multicast-direct has been enabled globally. 

E. WLAN has been set for a QoS value of Gold. 

F. RTSP is used to stream the video due to wireless multicast not using acknowledgements. 

View Answer

Q3. Refer to Exhibit. 

A wireless client is connecting to FlexAPI which is currently working standalone mode. The AAA authentication process is returning the following AVPs: 

Tunnel-Private-Group-ld(81): 15 Tunnel-Medium-Type(65):IEEE-802(6) Tunnel-Type(64): VLAN(13) 

Which three behaviors will the client experience? (Choose three.) 

A. While the AP is in standalone mode, the client will be placed in VLAN 15. 

B. While the AP is in standalone mode, the client will be placed in VLAN 10. 

C. When the AP transitions to connected mode, the client will be de-authenticated. 

D. While the AP is in standalone mode, the client will be placed in VLAN 13. 

E. When the AP is in connected mode, the client will be placed in VLAN 13. 

F. When the AP transitions to connected mode the client will remain associated. 

G. When the AP is in connected mode, the client will be placed in VLAN 15. 

H. When the AP is in connected mode, the client will be placed in VLAN 10. 

View Answer

Q4. A network engineer has installed 802.11ac access points with 80 MHz enabled; however, in the conference rooms, co-channel interference is being noticed. Under which tab in the RF profiles configuration can the engineer find the settings to tune the channel width for a group of APs? 

A. 802.11 

B. RRM 

C. High Density 

D. General 

View Answer

Q5. Which network is connected by default when connecting to the unused Ethernet port of a MAP? 

A. the native VLAN that the MAP is connected to 

B. the VLAN that is associated with WLAN number 1 in the WLC 

C. the native VLAN that the WLC is connected to 

D. the VLAN that is associated with the SSID that the MAPs are communicating on 

View Answer

Q6. You have just added a new MSE to Prime Infrastructure and want to synchronize the MSE with your 5508 WLC. which is located behind a firewall in a DMZ. You notice that NMSP messages are failing between the two devices. What traffic needs to be allowed on the Firewall to ensure the MSE and WLC can communicate using NMSP? 

A. UDP 16113 

B. TCP 1613 

C. TCP 16113 

D. UDP 1613 

View Answer

Q7. A customer has "quiet" wireless clients that use static IP addresses. Which two WLAN configurations are required for these wireless clients to connect properly? (Choose two.) 

A. Disable DHCP address assignment required. 

B. Enable passive client. 

C. Disable allow AAA override. 

D. Enable static IP tunneling. 

E. Disable DHCP server override. 

View Answer

Q8. A network engineer is viewing the QBSS information in a packet sniff. Which two QBSS characteristics are crucial for successful troubleshooting? (Choose two.) 

A. When only WMM is enabled, information element number 1 QBSS Load information element is sent out in the beacons and probe responses. 

B. When only WMM is enabled, information element number 3 QBSS Load information element is sent out in the beacons and probe responses. 

C. When the client CAC limit is supported, information element number 2 is sent out in the beacons and probe responses on the bg radios. 

D. When the client CAC limit is supported, information element number 1 is sent out in the beacons and probe responses on the bg radios. 

E. When only WMM is enabled, information element number 2 QBSS Load information element is sent out in the beacons and probe responses. 

View Answer

Q9. Which statement about when you configure FlexConnect APs and you want to set up Cisco Centralized Key Management fast roaming is true? 

A. FlexConnect groups are required for Cisco Centralized Key Management fast roaming to work with FlexConnect access points. 

B. APs that are in the same FlexConnect group but associated to different WLCs support Cisco Centralized Key Management. 

C. Cisco Centralized Key Management fast roaming among FlexConnect and non-FlexConnect access points is supported. 

D. The FlexConnect access point must be in standalone mode to support Cisco Centralized Key Management. 

View Answer

Q10. A network engineer is experiencing issues enabling LAG on the WLC. Which four characteristics should be validated to ensure LAG configuration? (Choose four.) 

A. All ports participate in the LAG by default when LAG is enabled on the controller, y 

B. Dynamic interfaces and management are moved to port 1 

C. Primary and secondary ports are needed for each interface. 

D. Multiple untagged interfaces to the same port are not allowed. 

E. EtherChannel must be configured for mode "on" on the switch. 

F. Only one functional physical port is needed to continue to pass traffic. 

G. Multiple LAGs are permitted on the controller. 

H. The WLC does not need to be rebooted to enable the LAG configuration. 

View Answer