Your success in Cisco 300-365 is our sole target and we develop all our 300-365 braindumps in a way that facilitates the attainment of this target. Not only is our 300-365 study material the best you can find, it is also the most detailed and the most updated. 300-365 Practice Exams for Cisco CCNP Wireless 300-365 are written to the highest standards of technical accuracy.


2026 New 300-365 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-365/

Q1. A customer requires that the remote site be able to utilize local servers when the AP is in WAN-down (standalone mode). Which AP mode must be configured on the wireless controller? 

A. SE-Connect 

B. Monitor 

C. Local 

D. FlexConnect 

E. Sniffer 

F. Rogue Detector 

Answer: D 

Q2. A network engineer must ensure that corporate wireless users have a better experience than guest wireless users. Which two configurations fulfil requirement? (Choose two.) 

A. Override per-SSID bandwidth contracts on the corporate WLAN to reserve bandwidth. 

B. Modify the corporate WLAN to the Platinum QoS policy. 

C. Enable 802.1ptag on the Gold QoS pofccyto honor prioritized traffic. 

D. Adjust the guest WLAN radio policy to 80211 b/g only. 

E. Change the guest WLAN to the Bronze QoS policy. 

Answer: B,E 

Q3. After a wireless deployment, users report that wireless voice clients are experiencing an unacceptable amount of delay while roaming during a call on the Cisco Unified 7925 Series phones. The customer environment consists of multiple controllers, all running 7.4.121.0 code, operating in a centralized deployment. What configuration issue is most likely contributing to the problem? 

A. The authentication should be set to WPA2-PSK to allow for 802.11n speeds for the Cisco Unified 7925 phones. 

B. The access points on that floor are all on one controller and should be load balanced evenly across multiple controllers. 

C. The access points for that floor are salt and peppered across multiple controllers and should be moved to the primary controller. 

D. The wireless phones are operating in the 2 4 GHz band and should be configured for the 5 GHz band. 

Answer: B 

Q4. By default, how long does a Mobility Services Engine wait for an echo response from a Wireless LAN Controller before declaring the neighbor dead? 

A. 10 Seconds 

B. 60 Seconds 

C. 15 Seconds 

D. 30 Seconds 

Answer: D 

Q5. An engineer must deploy FlexConnect APs to a site that typically has 300 ms latency to the WLC. Which typical operating mode must the engineer plan on for normal operations? 

A. local authentication, local switching 

B. central authentication, central switching 

C. central authentication, local switching 

D. connected mode 

Answer: A 

Q6. An engineer used an interface group under the SSID configuration, but noticed that a test client is getting an IP assigned in a different VLAN from the DHCP server. Which two options override the interface group configuration on the SSID? (Choose two.) 

A. static VLAN on client 

B. ACL 

C. AP group 

D. static IP on client 

E. MAC filtering 

F. RF group 

G. AAA override 

Answer: C,G 

Q7. An engineer wants to configure WebEx to adjust the precedence and override the QoS profile on the WLAN. Which configuration is needed to complete this task? 

A. Change the AVC application WebEx-app-sharing to mark 

B. Create an ACL for WebEx. 

C. Change the WLAN reserved bandwidth for WebEx. 

D. Create an AVC profile for WebEx marked with a lower DSCP value 

Answer: A 

Q8. A customer recently implemented WLC wireless multicast. Clients and connecting at the highest mandatory wireless rate of 24 Mbps and are receiving multicast traffic, but WLC cpu utilization and wired side network load has increased substantially. What three actions should the engineer take next to optimize the configuration? (Choose Three) 

A. verify that Global Multicast mode has been enabled 

B. verify that IGMP snooping is disabled on the wireless controller since the access points are handing IGMP messages from the clients. 

C. make sure the highest mandatory rate is set to 54 Mbps so that the multicast traffic has sufficient bandwidth 

D. verify Multicast Listener Discovery (MLD) v1 snooping has been enabled to keep track of and deliver IPv4 multicast flows 

E. change the wireless controller from Multicast-Unicastmodeto Multicast-Multicast mode and assign a multicast address in the 239.X.X.X/8 subnet 

F. verify that the L3 interfaces are configured for pirn sparse-dense-mode on the VLAN servicing the wireless access points as well as the wireless controller’s management VLAN 

Answer: A,B,E 

Q9. Which two methods to discover a controller does a MAP attempt when it boots up? (Choose two.) 

A. |f Ethernet and wireless are available, it attempts to discover only via Ethernet. 

B. if Ethernet is disconnected, it attempts to connect wirelessly using AWPP. 

C. if only wireless is available and it is configured as a MAP, it does not attempt to connect to a WLC. 

D. If Ethernet and wireless are available, it uses Ethernet first. If it cannot connect via Ethernet, then it chooses wireless. 

E. |f Ethernet is disconnected, it attempts to connect wirelessly using the configured DHCP option. 

Answer: A,B 

Q10. A customer has implemented a N+1 high availability plan in a multistory building. All APs on odd numbered floors are set as primary to WLC-A and all APs on even numbered floors are set as primary to WLC-8. Which two problems are likely to arise from this design? (Choose two) 

A. inconsistent CleanAir data due to multiple WLCs 

B. floor-to-floor bleed-through that causes intercontroller roaming delays 

C. AVC inconsistency due to multiple mobility group members 

D. legacy device compatibility with multiple WLC configuration that causes disconnects 

E. unpredictable AP loading during a WLC failure 

Answer: A,C