Want to know Ucertify 300-365 Exam practice test features? Want to lear more about Cisco Deploying Cisco Wireless Enterprise Networks certification experience? Study High quality Cisco 300-365 answers to Regenerate 300-365 questions at Ucertify. Gat a success with an absolute guarantee to pass Cisco 300-365 (Deploying Cisco Wireless Enterprise Networks) test on your first attempt.


2026 New 300-365 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-365/

Q1. You have a VoWLAN configured for platinum QoS, WMM, and CAC. IP phones for this VoWLAN include the Nokia and Cisco Unified Wireless IP Phones 7920G (pre-v2.0 firmware), 7921G, and 7925G. The Wireless IP Phones 7921G and 7925G work properly, but the Nokia and the Wireless IP Phones 7920G associate with the WLAN but cannot place calls. What is the issue? 

A. The lowest mandatory speed in the WLAN is too high and needs to be reduced. 

B. The Cisco Unified Wireless IP Phones 7920G and Nokia IP phones do not support TSPEC. 

C. EDCA needs to be enabled on the WLAN. 

D. HCCA needs to be enabled on the WLAN. 

E. The reserved roaming bandwidth setting is set too low. 

F. The expedited bandwidth setting needs to be enabled. 

Answer: B 

Q2. You have just added a new MSE to Prime Infrastructure and want to synchronize the MSE with your 5508 WLC. which is located behind a firewall in a DMZ. You notice that NMSP messages are failing between the two devices. What traffic needs to be allowed on the Firewall to ensure the MSE and WLC can communicate using NMSP? 

A. UDP 16113 

B. TCP 1613 

C. TCP 16113 

D. UDP 1613 

Answer: C 

Q3. Which of the following is not a Cisco RF fingerprinting key advantage over Location Tracking? 

A. Uses existing LWAPP-enabled Cisco Unified Networking components. 

B. Proprietary client hardware or software is required. 

C. Better accuracy and precision. 

D. Reduced calibration effort. 

Answer: B 

Q4. A customer recently implemented WLC wireless multicast. Clients and connecting at the highest mandatory wireless rate of 24 Mbps and are receiving multicast traffic, but WLC cpu utilization and wired side network load has increased substantially. What three actions should the engineer take next to optimize the configuration? (Choose Three) 

A. verify that Global Multicast mode has been enabled 

B. verify that IGMP snooping is disabled on the wireless controller since the access points are handing IGMP messages from the clients. 

C. make sure the highest mandatory rate is set to 54 Mbps so that the multicast traffic has sufficient bandwidth 

D. verify Multicast Listener Discovery (MLD) v1 snooping has been enabled to keep track of and deliver IPv4 multicast flows 

E. change the wireless controller from Multicast-Unicastmodeto Multicast-Multicast mode and assign a multicast address in the 239.X.X.X/8 subnet 

F. verify that the L3 interfaces are configured for pirn sparse-dense-mode on the VLAN servicing the wireless access points as well as the wireless controller’s management VLAN 

Answer: A,B,E 

Q5. A customer has limited staff to manage a wireless network. The customer wants a solution that requires minimum hardware. Which type of architecture do you propose? 

A. centralized 

B. distributed 

C. cloud-based 

D. unified 

Answer: A 

Q6. What address do PIM routers listen to in order to automatically discover the best RP for each multicast group? 

A. 224.0.0.13 

B. 224.0.1.39 

C. 224.0.0.14 

D. 224.0.140 

Answer: D 

Q7. Which statement about when you configure FlexConnect APs and you want to set up Cisco Centralized Key Management fast roaming is true? 

A. FlexConnect groups are required for Cisco Centralized Key Management fast roaming to work with FlexConnect access points. 

B. APs that are in the same FlexConnect group but associated to different WLCs support Cisco Centralized Key Management. 

C. Cisco Centralized Key Management fast roaming among FlexConnect and non-FlexConnect access points is supported. 

D. The FlexConnect access point must be in standalone mode to support Cisco Centralized Key Management. 

Answer: A 

Q8. What are two functions of the RAP in a mesh network? (Choose two.) 

A. It provides a wired connection for the wireless mesh APs. 

B. It adds capacity and resilience to a mesh area. 

C. it creates a centralized management location for the mesh network. 

D. it reduces the hop count to the wireless network that is connected to the edge. 

E. it routes traffic from the wireless mesh to the wired network. 

Answer: B,D 

Q9. A network engineer must configure a 5 GHz network to allow for the greatest density of radios possible with the least amount of co-channel interference. Which configuration best fulfills this requirement? 

A. Set 802.11 h Local Power constraint to 25 dBm. 

B. Set DCA to 20 MHz channels and enable Extended UNII-2 channels. 

C. Enable Event Driven RRM in 5 GHz with a sensitivity of High, n 

D. Configure TPC Power Threshold to -80 dBm and set interference Optimal Mode (TPCv2). 

Answer: B 

Q10. A wireless engineer at a convention center has been asked to provision an SSID that can accommodate 4,000 users during a conference. Which interface group configuration should be used? 

A. One interface with /20 mask 

B. Two interfaces with /21 mask 

C. Four interfaces with /22 mask 

D. Eight interfaces with /23 mask 

Answer: D