The Replace Guide To 300-365 exam dumps

Q1. Refer to Exhibit. 

A wireless client is connecting to FlexAPI which is currently working standalone mode. The AAA authentication process is returning the following AVPs: 

Tunnel-Private-Group-ld(81): 15 Tunnel-Medium-Type(65):IEEE-802(6) Tunnel-Type(64): VLAN(13) 

Which three behaviors will the client experience? (Choose three.) 

A. While the AP is in standalone mode, the client will be placed in VLAN 15. 

B. While the AP is in standalone mode, the client will be placed in VLAN 10. 

C. When the AP transitions to connected mode, the client will be de-authenticated. 

D. While the AP is in standalone mode, the client will be placed in VLAN 13. 

E. When the AP is in connected mode, the client will be placed in VLAN 13. 

F. When the AP transitions to connected mode the client will remain associated. 

G. When the AP is in connected mode, the client will be placed in VLAN 15. 

H. When the AP is in connected mode, the client will be placed in VLAN 10. 

View Answer

Q2. A network engineer observes a spike in controller CPU overhead and overall network utilization after enabling multicast on a controller with 500 APs. What feature is necessary to correct the issue? 

A. controller IGMP snooping 

B. unicast AP Multicast Mode 

C. broadcast forwarding 

D. multicast AP Multicast Mode 

View Answer

Q3. CMX Facebook WiFi can allow access to the network before authentication. Which two of the following options are available? (Choose two) 

A. Allow all the traffic before authentication and intercept HTTPs only. 

B. Allow HTTP traffic only before authentication and block all the traffic. 

C. Allow SNMP traffic only before authentication and block all the traffic. 

D. Allow all the traffic before authentication and intercept HTTP only. 

E. Allow HTTPs traffic only before authentication and block all other traffic. 

View Answer

Q4. A customer called into the support center with a problem ticket that involves wireless clients having to reauthenticate when they are walking around their office. After further investigation, it was discovered that the customer has two controllers in an N+1 deployment. Which action must the engineer take to troubleshoot the issue? 

A. Verify that the wireless controllers are in the same mobility group and that the access points are all on the primary controller. 

B. Under the SSID, make sure that 802.1 Iris configured and running for the clients. 

C. Make sure that the SSID has the authentication set to 802.1x with Cisco Centralized Key Management so the data clients can roam seamlessly. 

D. Verify the access points are spread out between the primary and secondary controller and that the controllers are in the same mobility group. 

View Answer

Q5. A network engineer is viewing the QBSS information in a packet sniff. Which two QBSS characteristics are crucial for successful troubleshooting? (Choose two.) 

A. When only WMM is enabled, information element number 1 QBSS Load information element is sent out in the beacons and probe responses. 

B. When only WMM is enabled, information element number 3 QBSS Load information element is sent out in the beacons and probe responses. 

C. When the client CAC limit is supported, information element number 2 is sent out in the beacons and probe responses on the bg radios. 

D. When the client CAC limit is supported, information element number 1 is sent out in the beacons and probe responses on the bg radios. 

E. When only WMM is enabled, information element number 2 QBSS Load information element is sent out in the beacons and probe responses. 

View Answer

Q6. A customer requires that the remote site be able to utilize local servers when the AP is in WAN-down (standalone mode). Which AP mode must be configured on the wireless controller? 

A. SE-Connect 

B. Monitor 

C. Local 

D. FlexConnect 

E. Sniffer 

F. Rogue Detector 

View Answer

Q7. An engineer must deploy FlexConnect APs to a site that typically has 300 ms latency to the WLC. Which typical operating mode must the engineer plan on for normal operations? 

A. local authentication, local switching 

B. central authentication, central switching 

C. central authentication, local switching 

D. connected mode 

View Answer

Q8. A customer has implemented a N+1 high availability plan in a multistory building. All APs on odd numbered floors are set as primary to WLC-A and all APs on even numbered floors are set as primary to WLC-8. Which two problems are likely to arise from this design? (Choose two) 

A. inconsistent CleanAir data due to multiple WLCs 

B. floor-to-floor bleed-through that causes intercontroller roaming delays 

C. AVC inconsistency due to multiple mobility group members 

D. legacy device compatibility with multiple WLC configuration that causes disconnects 

E. unpredictable AP loading during a WLC failure 

View Answer

Q9. On which AP radio or radios is Cisco WGB association supported? 

A. 2.4 GHz only 

B. 2.4 or 5 GHz only 

C. 2.4, 5, or 4.9 GHz 

D. 5 GHz only 

View Answer

Q10. A wireless engineer wants to enable optimized roaming for their 5GHz wireless network with these settings: -72dBm RSSI value, 25% coverage exception level percentage, and a minimum of 50 packets received. 

Which two commands achieve these settings? (Choose two.) 

A. config advanced 802.11a coverage data fail-percentage 25 

B. config advanced 802.11b optimized-roaming enable 

C. config advanced 802.11b coverage data rssi-threshold -72 

D. config advanced 802.11a optimized-roaming enable 

E. config advanced 802.11a coverage data rssi-threshold -72 

View Answer