Update Cisco 200-401 braindumps

Q1. - (Topic 2) 

Why is SSH preferred over Telnet as a method of accessing a network device to alter or view the configuration? 

A. Telnet encrypts only the login information, not the entire transmission. 

B. SSH requires fewer network resources and no additional configuration. 

C. Telnet is more difficult to use and configure than SSH. 

D. SSH encrypts the login and session information. 

View Answer

Q2. - (Topic 4) 

An Ethernet cable is attached to a PC NIC and then attached to a switch port. The PC power is turned on and the switch port link LED turns green. The link light indicates what two conditions? (Choose two.) 

A. Layer 2 communication has been established between the PC and switch. 

B. The PC has received a DHCP address. 

C. Traffic is being sent from the switch to the PC. 

D. If flashing, the green LED indicates port speed of 100 Mb/s. 

E. The Layer 1 media is functioning between the PC and switch. 

F. The switch port is functioning as a half-duplex connection. 

View Answer

Q3. - (Topic 1) 

Which of the following correctly pairs the dotted decimal subnet mask with the correct number of binary bits that represent the subnet mask? 

A. 255.255.255.192 and /25 

B. 255.255.255.248 and /28 

C. 255.255.255.224 and /26 

D. 255.255.255.248 and /27 

E. 255.255.255.240 and /28 

F. 255.255.255.240 and /16 

View Answer

Q4. - (Topic 5) 

Exhibit: 

Refer to the exhibit. A technician enters the exhibited commands to configure a new router on the plant floor, but receives an error message when attempting to save the configuration. What can the technician do to correct the problem? 

A. Enter the correct command. 

B. Enter the command at the correct prompt. 

C. Upgrade the amount of flash memory in the router. 

D. Erase NVRAM to make room for the configuration file. 

E. Add NVRAM because there is not enough room for the configuration file. 

View Answer

Q5. - (Topic 3) 

What should be done with unused conductors in copper unshielded or shielded twisted-pair network cables? 

A. terminate in their characteristic impedance 

B. trim back and properly insulate 

C. connect to protective earth 

D. splice to a used conductor 

View Answer

Q6. - (Topic 4) 

With a Cisco IE 2000 switch, what does a port status LED indicate when it is solid amber? 

A. The port is sending or receiving data. 

B. A link is present. 

C. No link is present. 

D. There is a link fault. 

E. The port is not forwarding. 

View Answer

Q7. - (Topic 4) 

You are a called upon to troubleshoot connectivity problems to a network device on a production floor. You have used ping and traceroute to verify that you cannot connect to the device from the management network. The network is 209.165.202.128/27 and the device has been given the IP address 209.165.202.158 and mask 255.255.255.224. You have verified that you can reach the device with your computer connected to the same switch as the device..What could be the cause of this problem? 

A. The device is set to the wrong subnet mask. 

B. The device is set to the wrong IP address. 

C. The device has no IP default gateway. 

D. The device is connected to a switchport in the wrong VLAN. 

View Answer

Q8. - (Topic 5) 

With a Cisco IE 2000 switch, what does a power status LED indicate when it is solid green? 

A. Power is present on the associated circuit and the system is operating normally. 

B. Power is present on the associated circuit, but there is no correlation to whether the system is operating normally. 

C. The system is operating normally, but power is not necessarily present on the associated circuit. 

D. Power is not present on the associated circuit and the power supply alarm is configured. 

E. The power status LED does not show solid green. 

View Answer

Q9. - (Topic 4) 

In which two ways could you minimize the impact of monitoring an industrial network? (Choose two.) 

A. Send random messages to a device and see what the response is. 

B. Do frequent ping sweeps to industrial devices to check for their proper operations. 

C. Make a copy of all the network traffic and analyze it offline. 

D. Use an industrial-network-grade IDS-IPS system. 

View Answer

Q10. - (Topic 2) 

What are the two most relevant factors in determining the class of administration that is required to maintain the telecommunications infrastructure? (Choose two.) 

A. the size of the infrastructure 

B. the complexity of the infrastructure 

C. the age of the infrastructure 

D. the industry that the infrastructure supports 

E. the physical environment of the infrastructure 

View Answer