Our pass rate is high to 98.9% and the similarity percentage between our 200-401 study guide and real exam is 90% based on our seven-year educating experience. Do you want achievements in the Cisco 200-401 exam in just one try? I am currently studying for the Cisco 200-401 exam. Latest Cisco 200-401 Test exam practice questions and answers, Try Cisco 200-401 Brain Dumps First.


2026 New 200-401 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-401/

Q1. - (Topic 4) 

What are two recommended tools or commands that allow you to troubleshoot connectivity between two devices in different IP networks? (Choose two.) 

A. show interface status 

B. show spanning-tree 

C. ping 

D. show interfaces gigabitEthernet x/y switchport 

E. traceroute 

F. show interface 

Answer: C,E 

Q2. - (Topic 5) 

What is a reason to use user EXEC mode on an industrial switch? 

A. to verify commands that you have entered 

B. to change terminal settings 

C. to configure VLAN parameters 

D. to configure parameters that apply to the entire switch 

Answer: B 

Q3. - (Topic 5) 

What are two benefits that are provided by proper grounding and bonding systems? (Choose two.) 

A. higher speed communications 

B. safe discharge of electrostatic energy 

C. lower equipment power consumption 

D. equipotential.termination points for equipment and cable shields 

E. lowest carbon footprint 

Answer: B,D 

Q4. - (Topic 2) 

EtherNet/IP is an Ethernet implementation of which protocol? 

A. CIP 

B. Industrial Protocol 

C. DeviceNet 

D. ControlNet 

Answer: A 

Q5. - (Topic 1) 

Which of the following correctly pairs the dotted decimal subnet mask with the correct number of binary bits that represent the subnet mask? 

A. 255.255.255.192 and /25 

B. 255.255.255.248 and /28 

C. 255.255.255.224 and /26 

D. 255.255.255.248 and /27 

E. 255.255.255.240 and /28 

F. 255.255.255.240 and /16 

Answer: E 

Q6. - (Topic 2) 

Which prompt is used to configure parameters for the Ethernet ports of an industrial switch? 

A. Switch(config-if)# 

B. Switch(config-if-ind)# 

C. Switch(config-line)# 

D. Switch(config-ind)# 

E. Switch(config-vlan)# 

Answer: A 

Q7. - (Topic 3) 

What should be done with unused conductors in copper unshielded or shielded twisted-pair network cables? 

A. terminate in their characteristic impedance 

B. trim back and properly insulate 

C. connect to protective earth 

D. splice to a used conductor 

Answer: A 

Q8. - (Topic 1) 

A small manufacturing company has a Class C network address on the plant floor and needs to create five subnets, each accommodating 25 endpoints. Which subnet mask needs to be configured? 

A. 255.255.240.0 

B. 255.255.255.128 

C. 255.255.255.192 

D. 255.255.255.224 

E. 255.255.255.240 

F. 255.255.255.248 

Answer: D 

Q9. - (Topic 4) 

At which Layer would you troubleshoot a cabling issue? 

A. Layer 1 

B. Layer 2 

C. Layer 3 

D. Layer 4 

Answer: A 

Q10. - (Topic 5) 

Which two reasons make mesh bonding systems most effective? (Choose two.) 

A. cover wide areas 

B. provide additional strength to floor structures 

C. provide low-impedance noise-equalizing paths 

D. create equipotential.grounding systems 

E. most cost-effective approach 

Answer: C,D