The Improve Guide To 200-401 dumps

Q1. - (Topic 1) 

Exhibit: Refer to the exhibit..Which port should a PLC with IP address 192.168.3.65 be plugged into in order to communicate to the rest of the network? 

A. FastEthernet1/1 

B. FastEthernet1/2 

C. FastEthernet1/3 

D. FastEthernet1/4 

E. FastEthernet1/5 

View Answer

Q2. DRAG DROP - (Topic 2) 

View Answer

Q3. - (Topic 1) 

Which option allows an EtherNet/IP I/O device to be safely installed where it is subject to water immersion? 

A. The device is rated IP20 and the power wiring is installed securely to the terminal block. 

B. The device is rated IP67 and a power cordset.is used. 

C. The device is rated IP67 and immersed to 10 m. 

D. The device is rated IP20 and immersed to 10 m. 

View Answer

Q4. - (Topic 4) 

An Ethernet cable is attached to a PC NIC and then attached to a switch port. The PC power is turned on and the switch port link LED turns green. The link light indicates what two conditions? (Choose two.) 

A. Layer 2 communication has been established between the PC and switch. 

B. The PC has received a DHCP address. 

C. Traffic is being sent from the switch to the PC. 

D. If flashing, the green LED indicates port speed of 100 Mb/s. 

E. The Layer 1 media is functioning between the PC and switch. 

F. The switch port is functioning as a half-duplex connection. 

View Answer

Q5. - (Topic 1) 

A small manufacturing company has a Class C network address on the plant floor and needs to create five subnets, each accommodating 25 endpoints. Which subnet mask needs to be configured? 

A. 255.255.240.0 

B. 255.255.255.128 

C. 255.255.255.192 

D. 255.255.255.224 

E. 255.255.255.240 

F. 255.255.255.248 

View Answer

Q6. - (Topic 4) 

What is the leading cause of fiber-optic link failure? 

A. contaminants 

B. crushed fiber 

C. poor testing practices 

D. bad connectors 

View Answer

Q7. - (Topic 5) 

Which three pieces of information must be maintained for all stakeholders as part of the change management process? (Choose three.) 

A. the location of the person who applied the change 

B. the date and time that the change was applied and on which device 

C. the original change request form that indicates why the change is necessary 

D. the size of the change (in bytes) 

E. a description of the actual change itself.(configuration, program code, and so on) 

F. the names of the current members of the change advisory board 

G. the industrial protocol that is used 

View Answer

Q8. - (Topic 4) 

Exhibit: 

Refer to the exhibit. The output that is shown is generated at an industrial switch. Which three statements are true? (Choose three.) 

A. All ports will be in a state of discarding, learning, or forwarding. 

B. Thirty VLANs have been configured on this switch. 

C. The bridge priority is lower than the default value for spanning tree. 

D. All interfaces that are shown are on shared media. 

E. All designated ports are in a forwarding state. 

F. This switch must be the root bridge for all VLANs on this switch. 

View Answer

Q9. - (Topic 3) 

With what are APC connectors used? 

A. Category 6a cables that need tight radius bends 

B. copper network cables in corrosive environments 

C. single-mode fiber-optic cables to reduce return loss 

D. high-density copper patch panels 

View Answer

Q10. - (Topic 2) 

An administrator has connected devices to an industrial switch and, for security reasons, wants the dynamically learned MAC addresses from the address table added to the running configuration. What must be done to accomplish this? 

A. Enable port security and use the keyword sticky. 

B. Set the switchport mode to trunk and save the running configuration. 

C. Use the switchport protected command to have the MAC addresses added to the configuration. 

D. Use the no switchport port-security command to allow MAC addresses to be added to the configuration. 

View Answer