The Updated Guide To 200-401 exam dumps

Q1. DRAG DROP - (Topic 2) 

View Answer

Q2. - (Topic 5) 

What is the most critical step to perform when you are using optical fiber connectors? 

A. Cover with dust caps when not in use. 

B. Immerse in alcohol prior to use. 

C. Blow off and carefully wipe down with a tissue before and after each use. 

D. Lightly sand with cloth prior to mating. 

View Answer

Q3. - (Topic 4) 

The network administrator is using a Windows PC application that is called putty.exe for remote communication to a switch for network troubleshooting. Which two protocols could 

be used during this communication? (Choose two). 

A. SNMP 

B. HTTP 

C. Telnet 

D. RMON 

E. SSH 

View Answer

Q4. - (Topic 2) 

Exhibit: 

Refer to the exhibit. An industrial ruggedized network device needs to be installed in the place of the icon labeled Network Device to accommodate a leased line attachment to the Internet. Which network device and interface configuration meets the minimum requirements for this installation? 

A. a router with two Ethernet interfaces 

B. a switch with two Ethernet interfaces 

C. a router with one Ethernet and one serial interface 

D. a switch with one Ethernet and one serial interface 

E. a router with one Ethernet and one modem interface 

View Answer

Q5. - (Topic 2) 

Exhibit: 

Refer to the exhibit. CCNA.com has the industrial network shown in the exhibit. All switches are configured as layer 2 switches and are using VLAN 1 as their management VLAN. Each VLAN 1 interface has been assigned the correct IP address. What is the purpose of assigning a default gateway to SW-C switch? 

A. allows connectivity between the VLAN 1 interface on SW-C and other devices in the network. 

B. allows connectivity between Host A and other devices in the network. 

C. allows connectivity between Host B and other devices in the network. 

D. allows the switch to pass traffic between Host A and Host B 

View Answer

Q6. - (Topic 1) 

Exhibit: Refer to the exhibit. What are three traffic and interconnection requirements for the devices in the exhibit? (Choose three.) 

A. The EtherNet/IP drive connections are in a high-voltage area and need protection from electromagnetic noise, so.shielded cable that is rated for 600 V.is advised. 

B. EtherNet/IP devices such as the controller, drive, VoIP phone, and IP camera should be in the same VLAN. 

C. CIP traffic has the highest bandwidth requirement so it needs the highest QoS setting. 

D. EtherNet/IP drive traffic has high sensitivity to random drops, latency, and jitter. 

E. Real-time motion control and VoIP traffic can share the same VLAN with the proper QoS setting. 

F. IEEE1588 and PTP are important for ensuring real-time synchronization. 

View Answer

Q7. - (Topic 5) 

Which two pieces of information are commonly tracked as part of a change management process? (Choose two.) 

A. reason for the change 

B. names of people involved in the change 

C. return on investment related to the change 

D. SWOT analysis related to the change 

E. scatter diagrams related to the change 

View Answer

Q8. - (Topic 2) 

Which three of the following components must be elected before the Spanning Tree Protocol can converge in a switched LAN? (Choose three.) 

A. designated ports 

B. duplex operating mode 

C. fast mode ports 

D. root bridge 

E. root ports 

F. BDPU priority 

View Answer

Q9. - (Topic 1) 

Exhibit: Refer to the exhibit..Which port should a PLC with IP address 192.168.3.65 be plugged into in order to communicate to the rest of the network? 

A. FastEthernet1/1 

B. FastEthernet1/2 

C. FastEthernet1/3 

D. FastEthernet1/4 

E. FastEthernet1/5 

View Answer

Q10. - (Topic 4) 

What are two symptoms of duplex mismatch? (Choose two.) 

A. Ping does not return from one direction versus the other direction. 

B. Communication is slow and locks up. 

C. Speed is seen equally slow in both directions. 

D. The half-duplex side sees frame sequence errors or runt frames. 

E. The full-duplex side sees CRC errors. 

View Answer