we provide Approved Cisco 200-401 free practice test which are the best for clearing 200-401 test, and to get certified by Cisco Managing Industrial Networks with Cisco Networking Technologies. The 200-401 Questions & Answers covers all the knowledge points of the real 200-401 exam. Crack your Cisco 200-401 Exam with latest dumps, guaranteed!


2026 New 200-401 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-401/

Q1. - (Topic 1) 

Exhibit: Refer to the exhibit..Which port should a PLC with IP address 192.168.3.65 be plugged into in order to communicate to the rest of the network? 

A. FastEthernet1/1 

B. FastEthernet1/2 

C. FastEthernet1/3 

D. FastEthernet1/4 

E. FastEthernet1/5 

Answer: C 

Q2. DRAG DROP - (Topic 2) 

Answer:  

Q3. - (Topic 5) 

What are two benefits that are provided by proper grounding and bonding systems? (Choose two.) 

A. higher speed communications 

B. safe discharge of electrostatic energy 

C. lower equipment power consumption 

D. equipotential.termination points for equipment and cable shields 

E. lowest carbon footprint 

Answer: B,D 

Q4. - (Topic 1) 

Exhibit: 

Which two statements are correct for a safe wiring installation to the terminal block of the switch or endpoint? (Choose two.) 

A. Insert a green ground wire into the terminal block that is marked RT for return. 

B. Verify that DC power is live and within 24 VDC voltage range before starting wiring. 

C. Verify that the DC power circuit includes an overcurrent protective device that limits the DC current to 5 A. 

D. Because this is a low-voltage DC circuit, anyone can install this wiring without electrical training or qualifications. 

E. Connect the positive 24 VDC conductor to the V terminal and connect the negative 24 VDC return wire to the RT terminal. 

F. A ground wire can optionally be connected to the screw terminal on the front of the switch. 

Answer: C,E 

Q5. - (Topic 5) 

Which two commands can help you to determine what image is running on your industrial switch? (Choose two.) 

A. show version 

B. show spanning-tree 

C. show interface-switch 

D. show interfaces gigabitEthernet x/y switchport 

E. show license 

Answer: A,E 

Q6. - (Topic 5) 

Which two pieces of information are commonly tracked as part of a change management process? (Choose two.) 

A. reason for the change 

B. names of people involved in the change 

C. return on investment related to the change 

D. SWOT analysis related to the change 

E. scatter diagrams related to the change 

Answer: A,B 

Q7. - (Topic 2) 

Which two ports does EtherNet/IP use to communicate? (Choose two.) 

A. TCP 44818 

B. UDP 44818 

C. TCP 502 

D. UDP 502 

E. TCP 2222 

F. UDP 2222 

Answer: A,F 

Q8. - (Topic 4) 

At which Layer would you check ACLs for TCP ports being blocked? 

A. Layer 1 

B. Layer 2 

C. Layer 3 

D. Layer 4 

Answer: D 

Q9. - (Topic 5) 

A router is not operating as expected and the network administrator wants to verify that the router booted using the correct IOS image. Which command should be used to determine which IOS is running on the router? 

A. show flash 

B. show version 

C. show memory 

D. show startup-config 

E. show config-register 

Answer: B 

Q10. - (Topic 5) 

Which protocol is a secure alternative to Telnet? 

A. SSH 

B. FTP 

C. SMTP 

D. SNMP 

E. HTTP 

Answer: A