Cause all that matters here is passing the Cisco 200-401 exam. Cause all that you need is a high score of 200-401 Managing Industrial Networks with Cisco Networking Technologies exam. The only one thing you need to do is downloading Ucertify 200-401 exam study guides now. We will not let you down with our money-back guarantee.


2026 New 200-401 Exam Dumps with PDF and VCE Free: https://www.surepassexam.com/200-401-exam-dumps.html

Q1. - (Topic 2) 

Given a ring topology, which loop prevention mechanism provides the fastest reconvergence time after a link failure? 

A. Rapid Per-VLAN Spanning Tree Protocol 

B. Resilient Ethernet Protocol 

C. Multiple Spanning Tree Protocol 

D. Spanning Tree Protocol 

Answer: B 

Q2. - (Topic 5) 

Which two reasons make mesh bonding systems most effective? (Choose two.) 

A. cover wide areas 

B. provide additional strength to floor structures 

C. provide low-impedance noise-equalizing paths 

D. create equipotential.grounding systems 

E. most cost-effective approach 

Answer: C,D 

Q3. - (Topic 4) 

What two things does a router do when it forwards a packet? (Choose two.) 

A. switches the packet to the appropriate outgoing interfaces 

B. computes the destination host address 

C. determines the next hop on the path 

D. updates the destination IP address 

E. forwards ARP requests 

Answer: A,C 

Q4. - (Topic 1) 

Exhibit: 

Refer to the exhibit. Host 3 on Network A is sending data to Host 8 on Network B. Which address is the default gateway of Host 3? 

A. the address of the switch interface that is connected to router interface Fa0/0 

B. the address of the switch interface that is connected to router interface Fa0/1 

C. the address of the host that is connected to Network A 

D. the address of the host that is connected to Network B 

E. the address of the router interface Fa0/0 

F. the address of the router interface Fa0/1 

Answer: E 

Q5. - (Topic 4) 

What is the leading cause of fiber-optic link failure? 

A. contaminants 

B. crushed fiber 

C. poor testing practices 

D. bad connectors 

Answer: A 

Q6. - (Topic 4) 

With a Cisco IE 2000 switch, what does a port status LED indicate when it is alternating green and amber? 

A. The port is sending or receiving data. 

B. A link is present. 

C. No link is present. 

D. There is a link fault. 

E. The port is not forwarding. 

Answer: D 

Q7. - (Topic 3) 

Which characteristic causes multimode fiber-optic cable to differ from single mode? 

A. by allowing multiple network services in the same cable 

B. shorter maximum network segment length for a given bandwidth 

C. a wider variety of available connector types 

D. use outdoors as well as indoors 

Answer: B 

Q8. - (Topic 1) 

A small manufacturing company has a Class C network address on the plant floor and needs to create five subnets, each accommodating 25 endpoints. Which subnet mask needs to be configured? 

A. 255.255.240.0 

B. 255.255.255.128 

C. 255.255.255.192 

D. 255.255.255.224 

E. 255.255.255.240 

F. 255.255.255.248 

Answer: D 

Q9. - (Topic 5) 

How does the optical time domain reflectometer use "backscattered" light to make measurements? 

A. It uses pulses to locate and test for sheath faults, damaged conductors, loose connectors, splices, bridge taps, split pairs, and other problems. 

B. It performs wiremapping to measure that all pins are correctly connected. 

C. It correlates the returned light pulses with a location in the fiber. 

D. It measures light-pulse width to measure that all pins are correctly connected. 

Answer: C 

Q10. - (Topic 4) 

What are two recommended tools or commands that allow you to troubleshoot connectivity between two devices in different IP networks? (Choose two.) 

A. show interface status 

B. show spanning-tree 

C. ping 

D. show interfaces gigabitEthernet x/y switchport 

E. traceroute 

F. show interface 

Answer: C,E