Examcollection 200-401 Questions are updated and all 200-401 answers are verified by experts. Once you have completely prepared with our 200-401 exam prep kits you will be ready for the real 200-401 exam without a problem. We have Renewal Cisco 200-401 dumps study guide. PASSED 200-401 First attempt! Here What I Did.
2026 New 200-401 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-401/
Q1. - (Topic 2)
Why is SSH preferred over Telnet as a method of accessing a network device to alter or view the configuration?
A. Telnet encrypts only the login information, not the entire transmission.
B. SSH requires fewer network resources and no additional configuration.
C. Telnet is more difficult to use and configure than SSH.
D. SSH encrypts the login and session information.
Answer: D
Q2. - (Topic 3)
Which option best describes a mechanical, ingress, climatic, chemical and electromagnetic environment that is classified as M3 I3 C3 E3?
A. the highest quality
B. office environment
C. severe
D. serviced by multiple cable segments
Answer: C
Q3. - (Topic 1)
Exhibit: Refer to the exhibit. What are three traffic and interconnection requirements for the devices in the exhibit? (Choose three.)
A. The EtherNet/IP drive connections are in a high-voltage area and need protection from electromagnetic noise, so.shielded cable that is rated for 600 V.is advised.
B. EtherNet/IP devices such as the controller, drive, VoIP phone, and IP camera should be in the same VLAN.
C. CIP traffic has the highest bandwidth requirement so it needs the highest QoS setting.
D. EtherNet/IP drive traffic has high sensitivity to random drops, latency, and jitter.
E. Real-time motion control and VoIP traffic can share the same VLAN with the proper QoS setting.
F. IEEE1588 and PTP are important for ensuring real-time synchronization.
Answer: A,D,F
Q4. - (Topic 4)
At which Layer would you check ACLs for TCP ports being blocked?
A. Layer 1
B. Layer 2
C. Layer 3
D. Layer 4
Answer: D
Q5. - (Topic 5)
Which two reasons make mesh bonding systems most effective? (Choose two.)
A. cover wide areas
B. provide additional strength to floor structures
C. provide low-impedance noise-equalizing paths
D. create equipotential.grounding systems
E. most cost-effective approach
Answer: C,D
Q6. - (Topic 5)
How does the optical time domain reflectometer use "backscattered" light to make measurements?
A. It uses pulses to locate and test for sheath faults, damaged conductors, loose connectors, splices, bridge taps, split pairs, and other problems.
B. It performs wiremapping to measure that all pins are correctly connected.
C. It correlates the returned light pulses with a location in the fiber.
D. It measures light-pulse width to measure that all pins are correctly connected.
Answer: C
Q7. - (Topic 2)
Which three of the following components must be elected before the Spanning Tree Protocol can converge in a switched LAN? (Choose three.)
A. designated ports
B. duplex operating mode
C. fast mode ports
D. root bridge
E. root ports
F. BDPU priority
Answer: A,D,E
Q8. - (Topic 5)
Which two pieces of information are commonly tracked as part of a change management process? (Choose two.)
A. reason for the change
B. names of people involved in the change
C. return on investment related to the change
D. SWOT analysis related to the change
E. scatter diagrams related to the change
Answer: A,B
Q9. - (Topic 2)
Exhibit:
Refer to the exhibit. An industrial ruggedized network device needs to be installed in the place of the icon labeled Network Device to accommodate a leased line attachment to the Internet. Which network device and interface configuration meets the minimum requirements for this installation?
A. a router with two Ethernet interfaces
B. a switch with two Ethernet interfaces
C. a router with one Ethernet and one serial interface
D. a switch with one Ethernet and one serial interface
E. a router with one Ethernet and one modem interface
Answer: C
Q10. - (Topic 4)
At which Layer would you check for spanning tree loops?
A. Layer 1
B. Layer 2
C. Layer 3
D. Layer 4
Answer: B